Installation And Start-Up - Fagor SM 8000 Guia De Inicio Rapido

■
DESCRIPTION
Analog TV modulator for video and audio Baseband,
●
to RF signal PAL (B / G, I, D / K) or SECAM
(L, D / K, B / G) for the mono model, or PAL B / G
or SECAM B / G for the stereo model. In the model
stereo audio output can be stereo or dual. The frequency
range RF output is between 47 and 862 MHz.
■

INSTALLATION AND START-UP

- The power sources must be disconnected from
the mains before connecting or disconnecting the
module.
Connect the earth connection of the frame to the earth
●
connection of the antenna installation.
Fix the modules to the frame in the order shown in the
●
application example (see page 3), with the power source
on the right and the amplifier on the left of the unit.
Connect the video and audio signal Baseband by the
●
connector (6) minidDIN 6.
Join the RF channel outputs (8) via the F-F coaxial bridge,
●
and load the free output of module 1 with 75 Ω, beside
the power source.
Connect the Supply bus BA 807 ref. 83807 between the
●
modules (5) and the SPS.
Connect the power source to the mains.
●
■
UCF 300: BUTTON FUNCTIONS
❏ ❏
The buttons are for vertical menu scrolling.
▲
▼
●
a) On the programming menu they are for selecting the
function to be programmed.
b) A parameter can be selected within a function.
c) A parameter setting can be modified within a
programmable parameter.
The buttons are for horizontal scrolling through the
●
programming menu, e.g.:
Function parameter
The button is for moving right.
●
The button is for exiting without changing the setting:
●
escape
The button is for validating the data item programmed.
●
OK
■
UCF 300: DISPLAY INDICATIONS
The UCF 300 control unit has two rows of alphanumerical
●
characters. The data display mode and programming
diagram on page 8 are a guide to this process:
If the characters are all upper case and on the upper
●
row, this indicates that one of the 4 functions has been
entered.
If data appear on two rows of the display, the
●
parameter to be adjusted is being displayed.
■
1. STANDARD: Standard output signal.
Mono Model
1.1. Standard:
Stereo Model
1.1. Standard:
2. RF OUTPUT: RF output
2.1. Out Frequency:
2.2. Out Level:
2.3. Out RF:
3. VIDEO/AUDIO: Parameters associated with
video and audio signals.
value. 3.1. Video Test:
3.2. Black Video:
3.3. Audio Level:
3.4. Audio Mode:
3.5. Audio Carrier Level:
10
The right arrow shows how to enter to change the
●
parameter setting.
A flashing box indicates that the parameter setting
●
can be modified using the
(press the button to validate).
OK
PROGRAMMING with UCF 300
Connect the UCF 300 to the desired module. After a
●
few seconds, the unit will show the model in question:
SM-ST 8000.
Press the button to enter the main programming
●
menu functions:
1. STANDARD
2. RF OUTPUT
3. VIDEO / AUDIO
4. MEMORY
❏ ❏
Press the button to scroll through the functions.
▲ ▼
●
Press the button to enter the parameters of the
●
desired function.
PAL B/G, PAL I, PAL D/K, SECAM L,
.
SECAM D/K, SECAM B/G
PAL B/G, SECAM B/G.
47 ÷ 862 MHz.
.
65 ÷ 80 dBμV
Enables/disables the RF output.
YES/NO
YES/NO
0 ÷ 12
Estéreo / Dual AB / Dual BA.
(Only on the stereo units).
12 / 16 dBc.
❏ ❏
▲
▼