PRASTEL MPROXMINI Manual Del Usuario página 2

MPROXMINI
1. GENERAL DESCRIPTION
MPROXMINI is a proximity reader with data output in Wiegand or Dataclock format. It can be connected both to Prastel MT15000/2, MT15000/EXT-4,
M1000E & M2000PE access control units and to other units that accept the data format generated by the reader.
MPROXMINI works with the proximity badges and tags MBPRO, MTAG, MBAD2, TPRO, MISOPROX, TELETAG®P-DT and the double technology
transmitter MPSDT2 & SLIM4E-DT.
All the electronic components and the antenna are assembled in an entirely sealed container with high resistance to atmospheric agents (IP67).
The MPROXMINI reader is equipped with a two-colour red/green LED and a buzzer to indicate the various functioning phases.
To install, assemble the reader and connect the cable to the access control unit in accordance with the instructions shown below.
2. TECHNICAL FEATURES
Power supply
Average absorption
Reading technology
Reading range
Signalling
Connection distance to the host
Insulation class
3. CONNECTIONS
RED
GRAY or BLACK
GREEN
WHITE
ORANGE
CYAN or BLUE
YELLOW
BROWN
VIOLET
PINK
4. FUNCTIONING
•
Power up the reader. The buzzer beeps once and the led turns on (red)
•
Place a badge, a tag or a double technology transmitter in front of the reader: the buzzer sounds, the LED turns into green and the code of the
badge is output at DATA0-DATA1 in Wiegand 30 bit format. The LED remains green and the PRESENCE line (PINK wire) goes low (0V) as long as
the badge is hold in the field of the reader. The standby status of the PRESENCE line is high (5V)
5. DATA FORMAT
If the MODE input (BROWN wire) is left unconnected or tied to 5VDC the output data format is Wiegand. If the MODE input is connected to GROUND the
output data format is DataClock.
While in Wiegand mode (BROWN wire unconnected or tied to 5VDC), if the WIEGAND FORMAT input (YELLOW wire) is left unconnected or tied to
5VDC, the data format at DATA0-DATA1 is 30-bit Wiegand. If the WFMT input is connected to GROUND, the data format at DATA0-DATA1 is 26-bit
Wiegand.
6. LED DRIVING
If the ORANGE and CYAN wires are left unconnected or tied to 5VDC the status of the led is driven by the reader itself.
If one or both of the ORANGE and CYAN wires are connected to GROUND, the status of the LED changes as follows:
ORANGE wire
GROUND
GROUND
5VDC or floating
7. ASSEMBLY INSTRUCTIONS
•
To assemble the reader, drill two 2.5 mm. holes in the support bracket for the fixing screws and one 6 mm diameter hole for the cable (fig. 1). Place
an insulating gasket around the hole. Hook-up the interface cable from the reader to the access control station and mount the reader using screws
with a max. diameter of 3 mm (fig. 2).
•
Fix the cover to the base, pressing until the hooks click into place (fig. 3).
•
Connect the reader to the host following the instructions in the table below and in the central unit installation manual. The table shows the
connections for the M1000E & M2000PE.
Keep in mind that installing the reader on metal surfaces could decrease the reading distance.
MPROXMINI
RED +12 Vdc
BLACK GROUND
GREEN DATA 0
WHITE DATA 1
DECLARATION OF CONFORMITY
Prastel declares that the following equipment PROXIMITY READER MPROXMINI IS IN ACCORDANCE with the 99/05/EC (R&TTE) directive.
The complete declaration of conformity is available in Prastel.
12 VDC
20 mA
Proximity - 125 KHz
8 cm with MBPRO
Bicolour led (red/green), buzzer
100 meters max.
IP 67
12 VDC
GROUND
DATA0 / DATA
DATA1 / CLOCK
Red LED driving
Green led driving
WIEGAND FORMAT
MODE
Not used
PRESENCE
CYAN wire LED status
GROUND OFF
5VDC or floating RED
GROUND GREEN
M1000E
10
7
9
8
INGLESE
M2000PE
PORT 1
9
6
8
7
ISMPROXMEU_05_14.DOC
M2000PE
PORT 2
18
15
17
16
0523