Product Familiarisation; Intended Use; Unpacking Your Tool; Before Use - Silverline 802165 Traducción Del Manual Original

GB
• When removing jammed or conflicting material, switch off the machine, remove the
mains plug, and wait for the blade to reach a complete halt.
• Never cut tiles that are too small to leave sufficient room for the hand to guide the tile
into the blade. When cutting smaller tiles ALWAYS use a push-stick.
• Only ever fit cutting disks that are recommended in the manufacturer's instruction
manual.
• Before using the tile cutter, always allow the cutting blade to reach the correct speed
and assess whether the blade is running smoothly, with no unfamiliar sounds or
vibrations. If unfamiliar characteristics are noticed, switch the machine off immediately
and unplug from the mains before attempting to evaluate the situation.
• Do not use excessive pressure on the cutting disk; doing so will not speed up the cut,
and will only cause excessive wear to the machine.
• NEVER use the tile cutter without the aid of cooling water; the water will maintain blade
temperature and prevent premature failure.

Product Familiarisation

1 Water Sump
2 On Button
3 Off Button
4 Table Surface
5 Cutting Disk
6 Riving Knife
7 Bevel Angle Lock Rear (not shown)
8 Bevel Angle Lock Front
9 Straight Fence
10 Fence Locking Knob
11 Mitre Guide
12 Fence Washer
13 Spanner
14 Spindle Spanner
15 Fence Fixing Brackets
16 Blade Guard Coach Bolt
17 Blade Guard Washer
18 Nut
19 Blade Guard
8

Intended Use

Precision water-cooled tile cutter for creating specific sized tiles. Features a straight fence,
mitre guide and an adjustable table angle for creating bevel cuts.

Unpacking Your Tool

• Carefully unpack and inspect your new tool. Familiarise yourself with all its features
and functions
• Ensure that all parts of the tool are present and in good condition. If any parts are
missing or damaged, have such parts replaced before attempting to use this tool

Before Use

WARNING: Ensure the tool is disconnected from the power supply before attaching or
changing any accessories, or making any adjustments.
Bench mounting
NOTE: Due to this machines physical attributes, it is intended to be secured to a bench, or
a secure flat work surface.
• Fasten to a secure, flat work surface using the two Bench Mounting Holes, located at
the front and rear (Image A)
Blade guard installation
1. Place the tile cutter on a secure flat surface and locate the Blade Guard (19)
2. Fit the Blade Guard over the Riving Knife, ensuring that the blade direction arrow on
the guard is facing towards the front of the machine (Image B)
3. Insert the Blade Guard Coach Bolt (16) through the square hole in the guard and
through the riving knife (Image C)
4. Fit the Blade Guard Washer (17) and adjust the height of the guard to provide
adequate clearance for the material to be cut
5. Fasten the Blade Guard to the Riving Knife using the Nut (18)
Straight fence installation
1. Ensure the Bevel Angle Lock Front (8) and Rear (7) are securely tightened, and
position the tile cutter on its side on a secure flat surface
2. Locate the Straight Fence (9), Fence Locking Knobs (10), Fence Washers (12) and the
Fence Fixing Brackets (15)
3. Hold the Straight Fence against the Table Surface (4) with the tabs facing towards
the bottom of the tile cutter (Image D)
4. Position the Fence Fixing Bracket behind the ridge that runs along the edge of the
Table Surface; place the washer onto the Fence Locking Knob and screw it into the
fixing bracket to secure the Straight Fence to the table (Image E)
5. Repeat step 4 for the other side of the Straight Fence
Water sump installation
:
WARNING Handling water around electronic equipment is hazardous. Take extra care
when handling water around the tile cutter. Always make sure the machine is switched off
at the mains beforehand.
1. Position the tile cutter on a secure flat surface
2. Locate the Water Sump (1)
3. Lift the side of the tile cutter that features the blade housing and place the Water
Sump so the blade housing sits inside (Image F)
4. To fill the Water Sump, add clean water to the sump until the level sits between the
'min' and 'max' markings on the blade housing
Operation
WARNING: ALWAYS wear eye protection, adequate respiratory and hearing protection, as
well as suitable gloves, when working with this tool.
:
WARNING
Prolonged use of this machine can cause the internal motor to overheat. To
prevent overheating of the motor, switch off and allow the machine to cool down after 10
minutes of consistent use.
:
WARNING Never operate this machine without water, dry operation will cause the
machine to wear out prematurely.
Switching on and off
• The green On Button (2) is located at the front of the machine, next to the red Off
Button (3)
• To Switch the machine on, Press the On Button
• To Switch the machine off, Press the Off Button