wolfcraft VLC 800 Traducción Del Manual De Instrucciones Original página 13

Intended use
This appliance which does not require any further tools is suitable for cutting vinyl and laminate to size and can exclusively
be used for processing:
• self-adhesive and non-self-adhesive vinyl or PVC panels with a maximum width of 46.5 cm and a maximum thickness
of 6 mm as well as
• laminate with a maximum width of 46.5 cm and MDF/HDF boards with a thickness of 11 mm + impact sound insulation
The blade of the vinyl and laminate cutter has been made from non-wearing material and comes with a special anti-stick
coating. In order to attain the best cutting results, possible residues of glue should be removed from the blade or from
the aluminium profile. Due to its special shape, the blade needs neither be ground and sharpened nor is it admissible.
The blade holder's screwed connection should be re-tightened, if necessary.
Attention: The screw joints on the blade holder must be tightened if necessary. The screw joints must only be tightened
to the extent that the cutting blade can be opened and closed at the handle with slight resistance (see illustrations, page 10).
Please note the illustrations on pages 2 - 10 how to assemble and operate the appliance.
Operating instructions
1. Raise the cutting blade with the handle upwards
2. Push the laminate board against the guide edge, so that a precise cutting angle of 90° will be created.
Hint: Support the other end of the laminate board, so that it will be pushed horizontally against
the guide edge.
3. A clean cut is achieved by pressing the cutting blade with the handle steadily downwards.
Please make sure to push the blade straight down, in order to get an optimal result.
4. Attention: Remove the angle stop before making angular & longitudinal cuts (e.g. for the end boards). The laminate or vinyl
must be guided against the cutting blade by applying gentle pressure with the free hand in order to achieve precise
positioning for the cut. The cutting blade must then be evenly pressed downwards with the guide hand at the grab handle.
(see illustrations, page 7).
5. Attention: When cutting laminate or vinyl with thicknesses from 5 - 11 mm to length, the right and left cutting bars must be
installed in the holes (position 2) (= as-delivered condition). When cutting laminate or vinyl with thicknesses below 5 mm
to length, the two cutting bars must be installed in the holes (position 1). A cleaner cut can be guaranteed by reducing
the distance to the blade (see illustrations, page 5).
Safety instructions:
• Operate the appliance only by using its handle; keep your fingers off the cutting area.
• Always operate the appliance alone!
• Leave the blade in its closed position, when the appliance is not in use. When opening the blade move it right to the limit stop
at rear.
• Do not make any modifications or changes to the appliance.
• Never sharpen the blade!
• Make sure that both you and the appliance have a safe position on a stable surface.
• Check before starting to work that the equipment used is properly installed (such as screwed connections).
• Make sure your clothing fits tightly (especially the sleeves) and that you wear eye protection.
• Keep children out of your workshop and store your equipment and tools in a secure place.
• Never let inexperienced personnel work with your equipment and tools without duly supervising and instructing them.
• Always work methodically, in a concentrated fashion and with sufficient lighting.
Guarantee
We provide a warranty of 10 years from the day of purchase on the wolfcraft
used for DIY purposes. The warranty only covers damage to the item purchased, and only such damage that can be attributed
to faulty material und poor workmanship. The warranty does not cover defects and damage that must be attributed
to improper use or insufficient maintenance. Nor does the warranty cover the usual wear and tear as well as defects
and damage, of which the customer has been aware when purchasing the equipment.
Warranty claims can only be asserted by producing the invoice or the till receipt.
The warranty granted by wolfcraft
withdrawal from the contract, price reduction, claims for damages or reimbursement of expenses).
Vinyl and laminate cutter
® does not in any way restrict your statutory consumer rights (i.e. contract performance,
t
® product you acquired, provided it is exclusively
13