Charge The Ipod/Iphone; Remove The Ipod/Iphone; Play With Bluetooth Device; Pair The Bluetooth-Enabled Devices - Lenco IPT-100 Manual De Instrucciones

4. Start to play the connected iPod/iPhone.
-
To pause/resume play, press the
button.
- To skip to a track, press the
buttons.
- To search during play: press and hold
, , buttons, then release to resume
 
H/G
normal play.
- To navigate through the menu: hold and
press M/CLOCK button, then press
select, and press
Note:
When you use , to navigate through the menu,
 
the interval between each operation should be
within some seconds, or it will return to normal
function.

Charge the iPod/iPhone

The docked iPod/iPhone begins to charge while
the unit is connected to AC power.

Remove the iPod/iPhone

1. Pull the iPod/iPhone out of the dock.
2. Raise up the buckle
module to original position

Play With Bluetooth Device

You can listen to music from a Bluetooth-enable
device via this player.

Pair the Bluetooth-enabled devices

The first time you connect your Bluetooth device
to this player, you need to pair your device to this
player.
Note:
- The operational range between this player
and a Bluetooth device is approximately
8 meters.
- Before you connect a Bluetooth device to
this unit, familiarize yourself with the
Bluetooth capabilities of the device.
- Compatibility with all Bluetooth devices is
not guaranteed.
- Any obstacle between this unit and a
Bluetooth device can reduce the
operational range.
- Keep this player away from any other
electronic device that may cause
interference.
/BT
BF
, ,

H/G
,
 
/BT to confirm.
BF
1
, and rotate the dock
2 .
1. Turn on the Bluetooth function on your device.
2. Switch player's source to Bluetooth, Display
panel shows "BLU T", then show "NO BT"
(if there's no Bluetooth device connected).

3. Press and hold "
control for seconds to activate Bluetooth
pairing mode, display panel shows "PAIR".
4. Search for Bluetooth device with your device.
5. Select "BLUEPORT" in the pairing list.
to
6. Enter default password "0000", if the pairing
succeeds, display panel shows "BLU T" again.
7. To disconnect connection, turn off the
Bluetooth function on your device or switch
the player to other source.
Tip
- If there's a connection exist, hold and press
/BT" button on remote control for
"
BF
seconds will re-activate the pairing mode,
the connection will be interrupted.
- If there's no other Bluetooth device pair with
this player in two minutes, the player will
recovery previous connection.
- The player will also be disconnected when
your device is moved beyond the operational
range.
- If you want to reconnect your device to this
player, place it within the operational range.
- If the device is moved beyond the operational
range, when it is brought back, please check if
the device is still connected with the player.
- If they are connected, display panel shows
"BLU T".
- If the connection is lost, display panel shows
"NO BT", follow the instruction above to pair
your device to the player again.

Listen to music from Bluetooth device

If the connected Bluetooth device supports

Advanced Audio Distribution Profile (A2DP),
you can listen to the music stored on the
device through the player.
If the device also supports Audio Video

Remote Control Profile (AVRCP) profile, you
can use the player's remote control to play
music stored on the device.
1. Pair your device with the player.
2. Start play music via your device (if it
support A2DP)
3. Use supplied remote control to control
play(if it support AVRCP)
- To pause/resume play, press the
button.
- To skip to a track, press the
buttons.
English 6
/BT" button on remote
BF
,

H/G
/BT
BF
,
