Black and Decker ASI300 Manual De Instrucciones página 12

Ocultar thumbs Ver también para ASI300:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

12 • ENGLISH
FEATURES (Fig. A)
1. Storage compartment cover
2. Pressure gauge
3. Air hose with universal valve adaptor
4. 12 Volt cord and plug
5. AC cord
6. Nozzles
7. On/OFF Switch
ADDITIONAL SAFETY INSTRUCTIONS
FOR INFLATORS
f Do not direct the nozzle or hose at animals or
bystanders.
f Never leave the inflator unattended when running.
f Only use the adaptors supplied.
f Store the inflator out of reach of small children.
f The gauge is intended as a guide only. Tyre pressures
should be regularly checked with a certified gauge.
f Do not over inflate any object as this may cause a risk
of injury.
f Before use, check the power supply cord for signs of
damage, ageing and wear.
f Do not use the appliance if the power supply cord or
mains plug is damaged or defective.
USE
Hose and cord storage (Fig. B)
The hose and ac cord are stored in the storage
compartment on top of the Inflator. The holes in both sides
of the cover (1) allow for the hose and cord to be fed out
from the compartment so that the compartment cover can
be closed while the Inflator is in use.
Fitting the accessories (Fig. C)
Your inflator is supplied with the standard tapered nozzles
and the needle inflator nozzle.
f To operate the universal valve adaptor, pull the lever
up. Place the valve adapter over the stem of the
inflation needle or tapered nozzle.
f Press the lever on the valve adapter down to lock in
it place.
f Place the inflation needle or tapered nozzle into the
item to be inflated.
Note: Always leave lever up when not in use.
Operate your Inflator only with the nozzles included or with
standard tyre valves.
Make sure that the universal valve adaptor is firmly locked
in place before turning the Inflator on.
Many inflatables, have an internal flap that prevents air
loss during inflation. Unless this flap is displaced by the
nozzle it will not inflate. Push the nozzle firmly into the
valve to make sure that you push this flap out of the way.
Store the inflation needle inside one of the tapered nozzles
and snap the tapered nozzles into the storage slots
located on the bottom of the Inflator.
Pressure gauge (Fig. D)
Warning! Too much air pressure causes a hazardous
risk of bursting. Check the manufacturer's maximum
pressure rating for items being inflated.
Your Inflator is equipped with a built-in pressure gauge
that will automatically shut off when a predetermined air
pressure is reached. The gauge, which is located on the
top of the Inflator, will give a pressure reading in p.s.i.
(pounds per square inch) as well as in bar. In the case of
vehicle tyres, it
is recommended that the pressure reading be verified by
checking with a separate tyre gauge.
Using the automatic shut-off feature (Fig. D)
Warning! Do not leave the inflator running unattended.
It could burst tyres or other items (Maximum pressure -
1103 kPa/160 psi/11.03 bar).
f Turn the ring on the pressure gauge until the pointer is
aligned with the required pressure.
f When the Inflator reaches the desired pressure, it will
automatically shut off.
f To obtain an accurate pressure measurement, turn the
Inflator OFF when reading the gauge. The gauge has
an accuracy of +/- 3% at any pressure reading.
Switching on and off (Fig. E and F)
The on/off switch (7) is located at the rear of the inflator
just below the storage compartment in the cavity that acts
as a carrying handle.
AC Mode
f Always fully extend the AC cord before each use.
f To turn the inflator on, connect the AC cord (5) and
press the left part of the switch (7) marked "AC".
f To turn the inflator off, partially press the right part of
the switch (7) marked "DC" to the "0" position.
12V DC Mode
Warning! Do not operate the inflator when the car
engine is running.
f Always fully extend the 12 Vdc cord before each use.
To turn the inflator on, plug the 12 Volt adaptor into
your vehicle's 12 Volt accessory socket and press the
right part of the switch (7) marked "DC"
f To turn the inflator off, partially press the left part of
the switch (7) marked "AC" to the "0" position.

Publicidad

Tabla de contenido
loading

Tabla de contenido