golmar DQ-CAM-GB2 Guía Rápida página 4

DQ-CAM-GB2 CAMERA INTERFACE
( ) SAFETY PRECAUTIONS
*
- Always disconnect the power supply before making modifications to the device.
- The fitting and handling of these devices must be carried out by
The wiring must run at least 40 cm away from any other wiring
-
- Install the DQ-CAM-GB2 module in a dry protected location free from the risk of dripping or
splashing water.
- Install the DQ-CAM-GB2 module with an FA-GB2A power supply.
- Do not place in humid, dusty or smoky locations, or near sources of heat.
- Ensure that the air vents are free from obstruction so that air can circulate freely.
- To prevent damage, the DQ-CAM-GB2 module must be firmly secured in place.
- Before connecting the device, check the connections of the DQ-CAM-GB2, the cameras and the
FA-GB2A power supply.
- Use the Golmar RAP-2150 cable (2x1mm ).
-Always follow the instructions contained in this manual.
( ) CHARACTERISTICS
*
DQ-CAM-GB2 module for the GB2 system (do not use RD-GB2A modules in the same installation):
-
'Building' installation:
O
-Up to 1 DQ-CAM-GB2 camera interface.
-Up to 4 analogue CCTV cameras (the cameras must have their own power supply).
-The camera interface must be installed on the door panel Bus side (see wiring diagram p. 4).
- Important: Do not install the camera interface in installations with the RD-GB2A
- DIP switches.
- Status LEDs.
- Install the DQ-CAM-GB2 module with an FA-GB2A power supply.
DESCRIPTION OF THE DQ-CAM-GB2 MODULE
( )
*
FRONT
c
d
Model: DQ-CAM-GB2
e
b
a
Power In-Use CAM1 CAM2
a b
CAM (1~4) CAM3 CAM4
f
( )
* For more information, see the TDQ-CAM-GB2 user manual (code 50122168) "
https://doc.golmar.es/search/manual/50122168
authorised personnel
.
2
bus amplifier
TOP
a. Status LEDs.
b. Buttons: control of CAM1~CAM4
video output.
c. Reserved.
DIP d. DIP switch.
1 2 3 4 5 6
e. Connect to analogue CCTV
BOTTOM cameras (1~4).
f.
DIN rail latch release.
g.
Bus input terminals.
h.
Bus output terminals.
BUS(OUT) BUS(IN)
g
h
".
2
DQ-CAM-GB2 CAMERA INTERFACE
INSTALLATION
( )
*
( )
*
Illustration of DQ-CAM-GB2 camera interface installation:
.
( )
*
Description of the DIP switch:
The DIP switch is located at the top of the module.
DIP
1 2 3 4 5 6
DIP
1 2 3 4 5 6
DIP
1 2 3 4 5 6
DIP
1 2 3 4 5 6
DIP
1 2 3 4 5 6
DIP
1 2 3 4 5 6
. DIP
1 2 3 4 5 6
DIP
1 2 3 4 5 6
DIP
1 2 3 4 5 6
( )
*
Description of the status LEDs:
Power: LED on, indicates that the device is operating normally.
In -use: LED on, indicates that the DQ-CAM-GB2 unit is broadcasting video.
CAM(1~4): Indicates the camera that is broadcasting video.
1 ( )
The CAM (1~4) LEDs blink when the monitor shows the image of more
than 1 camera.
In-Use
( )
* Description of the CAM1 to CAM4 buttons.
Press the CAM1 to CAM4 buttons to control the corresponding video output.
Press the CAM4 button for 3 sec to enable the monitor to display the image of all of the cameras.
Important: The monitor must be in auto-on or communication.
( )
For more information, see the TDQ-CAM-GB2 user manual (code 50122168)
*
https://doc.golmar.es/search/manual/50122168
The DQ-CAM-GB2 module can be mounted onto a
DIN rail (4 elements) by applying slight pressure.
To remove the DQ-CAM-GB2 module from the DIN
rail, use a flat screwdriver to lever it off, as shown in
Model: DQ-CAM-GB2
the drawing.
Power In-Use CAM1 CAM2
CAM(1~4) CAM3 CAM4
Leave DIP 1 and 2 in the OFF position.
Leave DIP 3 in the OFF position if cameras 3 and 4 have
not been installed.
Set DIP 3 to ON if camera 3 is installed.
Set DIP 4 to OFF if camera 4 is not installed.
Set DIP 4 to ON if camera 4 is installed.
Set DIP 5 to OFF if display 'Mode A' is required in order to show the image of more
( )
than one camera on the monitor screen , * see display mode table.
Set DIP 5 to ON if display 'Mode B' is required in order to show the image of more
( )
than one camera on the monitor screen , * see display mode table.
Set DIP 6 to OFF when the MM-GB2 module is not connected or it has no camera
connected.
Set DIP 6 to ON when the MM-GB2 module is connected or it has a camera
connected.
CAM(1~4)
Description
CAM1 video output
CAM2 video output
CAM3 video output
CAM4 video output
"
3
DIN 46277
DIP
1 2 3 4 5 6
Model: DQ-CAM-GB2
Power In-Use CAM1
CAM (1~4) CAM3
On indicator.
Off indicator.
1 ( )
Blinking indicator.
".