Using The Remote Control - Jensen AQTIVE II Manual De Montaje Y Uso

UK
D
F
1
NL
3
ESP
N
ASSEMBLY / GETTING STARTED
Check whether all the parts have been supplied. Refer to the over-
S
view on the left fold-out page of this brochure.
1.
Place the bed on its side.
2. Fit the legs to the corner attachments on the lower frame
FIN
(see illust. 1).
3.
Fasten the foot board using the four bolts that are already at
tached to the foot end of the bed. Also screw the two wood
screws supplied into the foot board. In the case of 210 cm beds,
use the separate attachment points, the four bolts supplied and
DK
the two wood screws (see illust. 2a and 2b).
4.
Attach the sidebar using two screws at a distance of
approximately 80 cm from the head end. Screw into the inside of
the lower frame. In the case of double beds, no side bar should
PL
be fitted between the beds (see illust. 3).
5.
Before fitting the two beds together, use the remote control to
move the head and foot ends to a horizontal position. Then fit the
attachment (illust. 4).
6.
Lay the reversible mattress and the top mattress on the bed. Pull
the material over the side bars and the foot board (illust. 6).
7.
Then insert the plug into the socket.
8.
The motor and the remote control have been set at the factory.
This setting may be lost if there is a power cut for any considerable
length of time. Refer to the paragraph on activating the remote control.
Before using the bed you should read the paragraph entitled 'Using
the remote control'.
ACTIVATING THE REMOTE CONTROL
Before using the bed you should read the paragraph entitled 'Using
the remote control'. Insert two batteries into the remote control (2 x
AAA type). Configure the remote control by pressing the button on
the control unit under the bed until it emits a double audible signal.
Then, within 20 seconds, move the joystick on the remote control to
the right or the left. The remote control is now adjusted to the control
unit and the motor under the bed. Repeat this procedure for remote
control number 2 for bed number 2.
ACTIVATING A REMOTE CONTROL FOR TWO BEDS
Press the red button on the control unit under bed number 1. You
will hear a single peep. Press the red button on the control unit
under bed number 2. You will hear two peeps. Move the joystick to
the right or to the left. The remote control will now be able to control
two beds at the same time.
ACTIVATING REMOTE CONTROL NO. 2 FOR BOTH BEDS
Press the joystick for 5 seconds. While pressing the joystick, also
press the red button once on the control unit under bed number 2.
Let go of the joystick. Remote control no. 2 is now set for both beds.
RESETTING THE FUNCTIONS
If you want to reverse the settings for the two beds and make it
possible to control beds 1 and 2 separately again, carry out the
procedure described under 'Activating the remote control'.
4
JENSEN AQTIVE II / III
INTRODUCTION
Congratulations on the purchase of your Jensen Aqtive III adjustable bed. We believe this
bed will give you many years of daytime and night-time comfort. We kindly request that you
study this manual closely before you start to assemble and install the bed.
GUARANTEE
If used normally, your Jensen Aqtive III is guaranteed for 5 years. The bill on which the
date of purchase is stated serves as a certificate of guarantee. In the event of any faults or
malfunctions, please contact the store from which you purchased the bed. When you do
so, you should state the model number shown on the motor (see illustration 5).

USING THE REMOTE CONTROL

3The bed can be moved to different positions using the remote control. Move the joystick
to the right or left to select the desired function. The function that you can control at any
given time is shown by an icon which lights up on the remote control (a small red light). You
can alter the selected function by moving the joystick up and down.
The various functions are:
2
1. Head end
2. Foot end
4
1+2. Head and foot end at the same time
3. Pressure point massage at head end
5
NB The Aqtive II does not have a massage function.
Press right or left to select the function. Then move up or down to change the massage
position. The series of lights (illustration 5) indicates the desired massage force. Turn off the
massage by switching off all the lights. The lights on the remote control go out after 15 seconds.
MEMORY
1. Move the bed to the preferred position you want (both the foot and the
head end, as desired). Press the joystick and keep it pressed until it starts
flashing.
2. When the head and/or foot end(s) is/are raised, press the joystick briefly
and the bed will return to the horizontal position.
3. To return the bed to your preferred position, briefly press the joystick and
the bed will move to the position saved in the memory.
MALFUNCTIONS
If you are unable to adjust the bed, proceed as follows:
• Reset the remote control. Refer to the paragraph entitled 'Activating the
remote control'.
•
Check whether the plug has been inserted properly into the socket and that
it is connected to the power supply.
•
Check whether there are batteries in the remote control and whether the
lights and symbols light up when you move the joystick. Replace the
batteries if they have run out.
• Remove the plug from the socket and repeat the procedure.
• Do not open the motor, the electrical components or the remote control
yourself. The producer does not accept any liability if an unauthorised person
has opened the motor, or has tampered with the electrical components or the
remote control. New parts must be obtained from an authorised supplier.
NOISE
A mechanical and electrically adjustable bed generates noise. The noise that
the bed makes may be reinforced by the acoustics of the room it is in. When
the massage function is activated, resonance may occur on a hard floor. You
can reduce this by laying a rug or some other material that absorbs vibrations
under the legs of the bed.
EMERGENCY FUNCTION
In the event of a power failure you can lower the bed by pressing the red but-
ton on the control unit and by keeping it pressed. For this to work there must
be two 9 V batteries in the control unit. Once this function has been used, the
batteries must be changed to ensure that this function will work again in the
event of a future power failure.
USAGE
The bed's lifting motors are not designed for continuous usage. The bed will
only continue to be reliable and operate for a normal life if the motors do not
operate for longer than 2 minutes during a 18 minute period. If this limit is
exceeded, the life of the products will be reduced and the guarantee will no
longer apply. The bed has been constructed in such a way that it can bear
a maximum weight of 150 kg kg, distributed equally over the entire surface
of the bed, from the head end to the foot end. If you exceed these limits, the
product will be damaged and the guarantee will no longer apply. It is important
that no-one is sitting on the head or foot end of the bed while the bed is raised
or is moving.
NB:
If used carelessly, items may become trapped by the bed's moving
parts. You should therefore keep the remote control out of the reach
of children!
ELECTRICAL DATA
Power supply: 230 V AC 50/60 Hz.
Standby power: Max 0.5W.
4. Pressure point massage at foot end
3+4. Rolling massage at head and
foot end at the same time
5. Set the desired massage force