TowSmart 777 Instrucciones De Instalación

READ ALL WARNINGS AND INSTRUCTIONS BEFORE INSTALLATION
WARNING: USE ONLY A 1 7/8" HITCH BALL WITH COUPLER FOR 1 7/8" HITCH BALL.
WARNING: AT NO TIME SHOULD THE MAXIMUM WORKING LOAD OF THE COUPLER BE EXCEEDED. THE MAXIMUM WORKING LOAD FOR
THE COUPLER IS 2000LB (907KG) MAX TRAILER WEIGHT.
WARNING: KEEP COUPLER OFF THE GROUND TO PREVENT DAMAGE AND DIRT BUILD UP.
INSTRUCTIONS NOTES:
THIS COUPLER IS DESIGNED TO BE WELDED OR BOLTED ONTO TRAILER
TONGUE.
WELD INSTRUCTIONS
(WITHOUT SPACERS ONLY.)
• SET WELDER TO 105-115 AMPS AND 18-22
VOLTS.
• USE NUMBER E6011 A.W.S. WELDING ROD.
• WELD 1/8" FILLET WELD AS SHOWN IN FIGURE 1.
BOLT INSTRUCTIONS
(WITH OR WITHOUT SPACERS.)
• CHECK THE COUPLER AND TRAILER TONGUE
TOUCH FULLY BEFORE INSTALL.
• USE FOUR (4) 3/8" BOLTS THROUGH SIDE
HOLES (FIGURE 2).
• TORQUE TO 20 FT-LBS (28N-M).
• AN ALTERNATIVE METHOD: USE TWO (2) 3/8"
GRADE 5 THROUGH BOLTS WITH LOCKNUTS
(FIGURE 3). TORQUE TO A MINIMUM OF
20 FT-LBS (28N-M). TAKE CARE AS NOT TO
DAMAGE THE COUPLER DURING
INSTALLATION.
CHECK THE COUPLER AND MOUNTING HARDWARE REGULARLY. IT IS RECOMMENDED TO CHECK AFTER THE FIRST TEN (10) MILES
(16KM) AFTER INSTALLATION. OIL MOVING PARTS TO PREVENT RUST BUILD UP.
THE ATTACHMENT AND INSTALLATION OF THIS PRODUCT IS CRITICAL AND BEYOND THE CONTROL OF WINSTON PRODUCTS, LLC.
WINSTON PRODUCTS, LLC IS NOT RESPONSIBLE FOR ANY DAMAGE THAT COULD RESULT FROM IMPROPER USE, INSTALLATION, OR
ATTACHMENT. AT NO TIME SHOULD THE SAFE WORKING LOAD OF THIS PRODUCT BE EXCEEDED.
LEA TODAS LAS ADVERTENCIAS E INSTRUCCIONES ANTES DE LA INSTALACIÓN
ADVERTENCIA: UTILICE SOLO UN ENGANCHE DE BOLA DE 1 7/8" CON EL ACOPLADOR PARA ENGANCHES DE BOLA DE 1 7/8".
ADVERTENCIA: EN NINGÚN MOMENTO SE DEBE EXCEDER LA CARGA MÁXIMA DE TRABAJO DEL ACOPLADOR. LA CARGA MÁXIMA DE TRA-
BAJO PARA EL ACOPLADOR ES DE 2000 LIBRAS (907 KG), EL PESO MÁXIMO DEL REMOLQUE.
ADVERTENCIA: MANTENGA EL ACOPLADOR DESPEGADO DEL SUELO PARA EVITAR DAÑOS Y ACUMULACIÓN DE SUCIO.
NOTAS SOBRE LA INSTALACIÓN:
ESTE ACOPLADOR ESTÁ DISEÑADO PARA SER SOLDADO O ATORNILLADO AL PUNTO DE ENGANCHE DEL REMOLQUE.
INSTRUCCIONES DE SOLDADURA (SIN ESPACIADORES SOLAMENTE).
• CONFIGURE EL SOLDADOR A 105-115 AMPERIOS Y 18-22 VOLTIOS.
• UTILICE UNA VARILLA PARA SOLDAR NÚMERO E6011, SEGÚN LO ESTABLECIDO POR LA SOCIEDAD AMERICANA DE SOLDADURA
(AMERICAN WELDING SOCIETY, AWS).
• HAGA UNA SOLDADURA EN ÁNGULO DE 1/8" COMO SE MUESTRA EN LA FIGURA 1.
®
COUPLER FOR 1 7/8" BALL WITH 3"CHANNEL WIDTH
INSTALLATION INSTRUCTIONS
INSTRUCCIONES DE INSTALACION
CONSIGNES D' INSTALLATION
FIGURE 2
FIGURE 1
FIGURE 3
PART #777