Tabla de contenido
Publicidad
Enlaces rápidos
Printed in U.S.A.
© 2012 Illinois Tool Works Inc.
903034-4
04/12
Part No. 903000
CORDLESS 20
FRAMING NAILER
°
USE 20 DUO-FAST ROUND
HEAD NAILS ONLY
IMPORTANT
DO NOT DESTROY
It is the customer's responsibility to
have all operators and service personnel
read and understand this manual.
OPERATING MANUAL
°
Publicidad
Tabla de contenido
Manuales relacionados para DUO-FAST 903000
Resumen de contenidos para DUO-FAST 903000
- Página 1 Part No. 903000 CORDLESS 20 ° FRAMING NAILER ° USE 20 DUO-FAST ROUND HEAD NAILS ONLY IMPORTANT DO NOT DESTROY It is the customer's responsibility to have all operators and service personnel read and understand this manual. Printed in U.S.A.
-
Página 2: Introduction And Warranty
ONE-YEAR LIMITED WARRANTY Duo-Fast's sole liability hereunder will be to replace any part or accessory which proves to be defective within the specific time period. Any replacement A one-year warranty will apply to all parts, except those listed... -
Página 3: Tabla De Contenido
Contents Introduction and Warranty............2 An Overview of the Duo-Fast Cordless 20° Framing Nailer..4 Safety Instructions..............5 Battery and Charging System ........... 8 Fuel Cell and Metering Valve ..........10 Preparing the Duo-Fast Cordless 20° Framing Nailer for Use.13 Duo-Fast 20° Cordless Framing Nailer Operation ....14 Fasteners and Applications ............. -
Página 4: An Overview Of The Duo-Fast Cordless 20° Framing Nailer
An Overview of the Duo-Fast 20° Cordless Framing Nailer ® Description Specifications Dimensions: Weight(with battery) 7.3 pounds The Duo-Fast Cordless Framing Nailer is a self-contained, Height 14 1/2 inches fully portable nailer that uses liquid hydrocarbon fuel to Length 12 inches power a unique linear drive internal combustion motor. - Página 5 The following safety instructions have been included in this booklet to provide you with basic information necessary for WARNING safe operation of the Duo-Fast Cordless Framing Nailer. DO NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTAND ALL SAFETY Never expose or store the PRECAUTIONS AND MANUAL INSTRUCTIONS.
-
Página 6: Safety Instructions
If the problem cannot be Nailer must be operated corrected, stop using the tool and report it to your only when it is in contact supervisor or Duo-Fast representative. with the work surface. When fastening thin 6. DO NOT LOAD FASTENERS WITH THE TRIGGER... - Página 7 Battery Disposal: The Duo-Fast Cordless batteries contain cadmium and must be recycled or disposed of properly. It is illegal in some areas to place a nickel-cadmium battery into the trash or solid waste stream. You may contact your local recycling center for information on where to return the spent battery or call 1-800-822-8837 for information on Ni-Cd battery recycling in your area.
-
Página 8: Battery And Charging System
120V AC outlet. Set the Duo-Fast batteries. It will accept an oval shaped battery. charger on a stable surface and insert the wall mount... -
Página 9: Inserting Battery
Battery and Charging System Battery Indicator Light The illustration is a close-up of the side of the Duo-Fast Cordless Framing Nailer handle. On the side of the handle is a small plastic lens. This is the battery indicator light. When you insert a fully-charged battery into the tool, you will see a blinking green light. -
Página 10: Fuel Cell And Metering Valve
NOTE: Altitude Restriction Never inhale the spray. Duo-Fast Cordless technology is powered by an Keep out of the reach of children. internal combustion engine and are effected by altitude. The tool may lose power or not cycle Store fuel cell(s) in well-ventilated areas only. - Página 11 Duo-Fast Cordless Fuel Cell Disposal Guidelines Duo-Fast provides this information to assist users with the proper disposal of discarded fuel cells. Acceptable disposal options vary depending on the type of fuel cell users. All users must consider federal, state and local solid waste regulations to ensure that discarded fuel cells are disposed of properly.
- Página 12 Fuel Cell and Metering Valve Inserting Fuel Cell As you slide the metering valve/fuel cell assembly into the Cordless Framing Nailer, you will notice a red adapter at the Inserting the metering valve/fuel cell assembly into the top of the cylinder pocket. As shown in the illustration, this Cordless Framing Nailer is very simple.
- Página 13 Duo-Fast Cordless Framing Nailer and Outdoor Weather The Duo-Fast C ordless Framing Nailer drives 20° round ® head nails only. The of nails that do not meet Duo-Fast Use the Cordless Framing Nailer outdoors, in clear weather, ® standards could cause tool damage and void your warranty.
-
Página 14: Duo-Fast 20° Cordless Framing Nailer Operation
Duo-Fast Cordless 20 ° Framing Nailer Operation PRESS THE WORK CONTACTING ELEMENT Move up to Increase AGAINST THE Drive Depth WORK SURFACE. Move Down to Reduce Fan motor starts, Drive Depth fuel is injected into combustion chamber and mixed with air by the fan. -
Página 15: Fasteners And Applications
Ring Shank - The ring shank provides improved withdrawal resistance for applications where the resistance from smooth The Duo-Fast Cordless Framing Nailer is not recommended for use with 3" (75mm) Ring Shank nails in pressure treated lumber shank fasteners is not adequate: floor decking, crating,... -
Página 16: Servicing
Framing Nailer, clearing a jammed fastener is easy: DANGER 1. Remove the fuel cell and battery. Never attempt any maintenance of the Duo-Fast Cordless 2. Lock follower back in magazine and remove fasteners. Framing Nailer without first removing the fuel cell and 3. -
Página 17: Air Filter
Soap and water restores the Cordless Faming Nailer Cordless Tool filter to a "like new" condition. Accessories A variety of accessories are available for the Duo-Fast Cordless Framing Nailer: Grille No-Mar Work Contacting Element - Part No. 903033 Battery - Part No. -
Página 18: Troubleshooting
Spark wire out of spark plug. Remove cap and check spark lead, insert in spark plug and replace cover. Spark plug is dirty. Clean tool cylinder head and spark plug. No spark is generated. Return tool to authorized Duo-Fast dealer for service. - Página 19 Work-contacting element is bent or is dirty. Clean or replace work-contacting element. tool cycles. If tool will not operate after following the above service directions, return the tool to an authorizes Duo-Fast representative for service. For Technical Support call 1-866-443-5754.
- Página 20 An Illinois Tool Works Company 955 National Parkway Schaumburg, IL 60173 www.duo-fastconstruction.com...