Kinderkraft SPINSTEP Manual Del Usuario página 18

II Installation of the tricycle:
How to video on: www.youtube.com/KinderkraftOfficial
Slide the rear wheels (2) in the frame (1) until you hear a click (Fig. A). Attach the mudguard (5) to the front fork (4) using a
screw (21) and mounting spanner (9). Make sure that the notch on the mudguard is in the front (Fig. B). Slide the front wheel
components together, put the front wheel (3) in the fork (4) and tighten the front fork fixing screws (6), using mounting
spanner (9) (Fig. C). Slide the front fork into the bike frame. Then place the front basket (22) on the frame (1), by matching
the holes to the basket's knobs. Attach the handlebars (8) to the frame (1) using the spanner (9) and fixing screw (7), so there
is no play (Fig.D). Make sure the front wheel is in the straight position before mounting the handlebar. Fix the bell (10) to the
handlebars (8). Put the pull rod (20) by inserting its more curved end from above in the opening on the left side of the fork
(4) (Fig.E.I) and fix the other end under the frame (1) into the hole at the point of attachment of the parent handle (Fig. E.II).
Make sure that the clamp is installed correctly, if it is placed in the wrong hole, the handlebar and parental grip will not be
positioned parallel. Place the seat base (25) on the frame. make sure that the wider side of it is positioned corre ctly (Fig.F).
Use the fixing screw (12) to attach the basket (11) to the frame (1) (Fig. G). Push the seat screw through the hole in the base
and frame (1), and fix the seat forwards or backwards by tightening the nut (23) on the bottom of the frame (Fig.H ), attach
the backrest (15) (Fig.I). Then place the guardrails (14) in the holes in the seat (13) (Fig.J). Then put on the seat cover (16), by
placing the side covers through the safety rails, pull the material onto the seat and connect the cover to the backrest by
repositioning the safety belts (Fig.K). To install the seat belts correctly, unfasten the buckle at the back of the backrest, then
pass the belts through the holes in the backrest and fasten the buckle (Fig.L). Once the belts have been correctly positioned,
install the crotch protection strap by placing the material on one of the safety railings. The safety rails should be connected
together, a click sound means the elements have been fixed correctly. Insert the visor (17) in the sides of the backrest (15)
(Fig.M). Fix the cupholder (19) to the parent handle (18) and insert it in the hole on the frame until the latch is locked (Fig.
M). Attach the sachet (26) to the parent handle and close the Velcro fasteners.
Adjusting:
Cover location − press the red buttons on both sides of the cover and set in a convenient position. You can also use buckles
on top of the cover.
Footrests − depending on the level of child development, the footrests can be folded to enable the child to ride the tricycle.
Whenever footrests are unfolded, enable the pedal lock in the front wheel (red button). WARNING! Whenever the parent's
handle is mounted and the footrest is unfolded, the wheel lock should be disengaged so that the pedals rotate freely without
causing the wheel to move (transmission off). Without disengaging the lock, feet may be crushed or injured! After removing
the parent handle, fold up the footrest and engage the wheel lock so that the pedals set the wheel in motion (transmission
on).
Brake - the bike has a rear wheel brake. Press the brake with your foot. If you hear the lock sound, the brake is activated. It
is released when the brake lock is lifted.
Harness − adjust the length to hold the child firmly, but not to block movements.
Seat position − the seat can be adjusted forwards and backwards, and turned rearwards. To do this, unscrew the nut (22) and
set the appropriate position. After tightening, make sure the seat is securely fastened.
Folding the rear wheels − slightly lift the tricycle and push the red button under the frame, rotate the rear wheels forwards.
Older children can ride without a backrest − slide the seat cover down, remove the backrest unlocking the levers on its sides,
rotate the guardrails 90° backwards and pull out. To ride without the backrest, the child should wear additional harness which
is located under the seat.
Adjusting the length of the parent handle − unfold and lock in a comfortable position.
III Maintenance and cleaning
Seat cover, backrest, handlebars cover: Remove from the frame. Wash at max. 30°C, gentle process. Do not bleach. Do not
dry in a tumble dryer. Do not iron. Do not dry clean.
Visor: Do not wash. Do not bleach. Do not dry in a tumble dryer. Do not iron. Do not dry clean. Clean with a clean and damp
cloth using mild soap. Allow to air dry. Do not immerse in water.
Frame: Clean the metal frame with a soft, clean and damp cloth using mild soap.
Storage
Keep out of the reach of children.
IV Warranty
1. All Kinderkraft products are covered by a 24-month warranty. The warranty period begins on the date of releasing the
product to the Buyer.
2. The warranty is valid for products sold in the following countries: France, Spain, Germany, Poland, United Kingdom, Italy.
3. In countries not listed above warranty terms and conditions are determined by the Seller.
4. It is possible to extend the warranty period to 120 months (10 years). Full text of the terms and conditions and warranty
extension registration form are available at
5. The warranty is valid only in the country where the purchase was made.
6. Complaints should be submitted by completing the form available at
7. The warranty shall not cover:
WWW.KINDERKRAFT.COM
18
WWW.RMA.KINDERKRAFT.COM