Tabla de contenido
Publicidad
Sandblasting Kits
Troubleshooting Chart
Symptom
Low or no air pressure
Material not blasting from gun
Gun will not shut off - trigger
stuck
Sputtering - low vacuum
Sputtering - air/abrasive leaks at
nozzle/jet area
Sputtering - vacuum leak
Sputtering - particle clogging
Limited Warranty
1.
DURATION: From the date of purchase by the original purchaser as follows: Standard Duty Products - One Year, Serious Duty Products - Two Years,
Extreme Duty Products - Three Years.
2.
WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (800)
543-6400
3.
WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld product.
4.
WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld nailer, stapler, air tool, spray gun, inflator or air accessory supplied or
manufactured by Warrantor.
5.
WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the duration of the warranty period.
6.
WHAT IS NOT COVERED UNDER THIS WARRANTY:
A.
Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM THE DATE OF ORIGINAL
PURCHASE AS STATED IN THE DURATION. If this product is used for commercial, industrial or rental purposes, the warranty will apply for ninety (90)
days from the date of purchase. Some States do not allow limitation on how long an implied warranty lasts, so the above limitations may not apply
to you.
B.
ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR
MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
C.
Any failure that results from an accident, purchaser's abuse, neglect or failure to operate products in accordance with instructions provided in the
owner's manual(s) supplied with product. Accident, purchaser's abuse, neglect or failure to operate products in accordance with instructions shall
also include the removal or alteration of any safety devices. If such safety devices are removed or altered, this warranty is void.
D.
Normal adjustments which are explained in the owner's manual(s) provided with the product.
E.
Items or service that are normally required to maintain the product, i.e. o-rings, springs, bumpers, debris shields, driver blades, fuses, batteries,
gaskets, packings or seals, fluid nozzles, needles, sandblast nozzles, lubricants, material hoses, filter elements, motor vanes, abrasives, blades, cut-off
wheels, chisels, chisel retainers, cutters, collets, chucks, rivet jaws, screw driver bits, sanding pads, back-up pads or any other expendable part not
specifically listed. These items will only be covered for ninety (90) days from date of original purchase. Underlined items have warranty for defects
in material and workmanship only.
7.
RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor's option, products or components which are defective, have
malfunctioned and/or failed to conform within duration of the warranty period.
8.
RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:
A.Provide dated proof of purchase and maintenance records.
B. Deliver or ship the Campbell Hausfeld product or component to the nearest Campbell Hausfeld Authorized Service Center. Freight costs, if any, must be
borne by the purchaser.
C.
Use reasonable care in the operation and maintenance of the products as described in the owner's manual(s).
9.
WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be scheduled and serviced according
to the normal work flow at the servicing location, and depending on the availability of replacement parts.
This Limited Warranty applies in the U.S. and Canada only and gives you specific legal rights. You may also have other rights which vary from state to state or
country to country.
Printed in Taiwan
Possible Cause(s)
1.
Regulator set incorrectly
2.
Pinched hose
3.
Dirty compressor filter
1.
Clogged material hose
2.
Buildup around jet
3.
Damp or heavy material
4.
Water in air supply
Damaged o-rings in air valve
1.
Worn jet and/or nozzle
2.
Abrasive buildup around jet/nozzle
1.
Loose nozzle or jet
2.
Damaged o-ring
1.
Loose material hose
2.
Damaged o-ring
Hose connector hole is covered
4
Corrective Action
1.
Reset regulator
2.
Straighten hose
3.
Clean or replace filter
1.
Lower the pressure below 40 PSI.
Firmly hold the gun tip flat against
the ground and pull the trigger to
force the material back out of the
material hose
2.
Remove nozzle and clean around jet
3.
Replace with dry abrasive. (Damp
material can be dried and reused)
4.
Drain air tank and install air filter, See
"Moisture in Compressed Air" box
Remove and replace o-rings
1.
Replace jet and/or nozzle
2.
Remove nozzle and jet and clean.
Make sure the threads are clean
before re-assembling
1.
Tighten nozzle or jet
2.
Replace o-ring
1.
Tighten material hose
2.
Replace o-ring
Uncover hose connector hole
www.chpower.com
Publicidad
Tabla de contenido
