Before Using - Black+Decker GGR5000 Manual De Instrucciones

f Damage to unit: If you strike or become entangled
with a foreign object, stop tool immediately, unplug,
check for damage and have any damage repaired
before further operation is attempted. Do not operate
with a broken hub or spool.
f Avoid dangerous environmental conditions:
Do not use electric tools in damp or wet locations.
Follow all instructions in this instruction manual for proper
operation of your tool. Don't use the tool in the rain.
f Do not operate portable tools in gaseous or
explosive atmospheres: Motors in these tools
normally spark, and the sparks might ignite fumes.
f Store idle tools indoors: When not in use, tools
should be stored indoors in a dry, locked-up place out
of reach of children.
f Stay alert: Watch what you are doing. Use common
sense.
f Do not operate tool when you are tired.
f Maintain appliances with care: Follow instructions
in maintenance section. Inspect extension cords
periodically and replace if damaged. Keep handles
dry, clean and free from oil and grease.
f Check damaged parts: Before further use of the
appliance, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any
other condition that may affect its operation. A guard
or other part that is damaged should be properly
repaired or replaced by an authorized Service Center
unless otherwise indicated elsewhere in this manual.
f Keep the handles free from oil and fuel.
f Always use proper handles and shoulder strap
when cutting.
f Do not smoke while mixing fuel or filling tank.
f Always mix and store fuel in a properly marked
container that is approved by local codes and
ordinances for such usage.
f Never remove the fuel tank cap while the engine
is running.
f When ever approaching an operator of the machine,
carefully call his attention and confirm that the operator
stops the engine. Be careful not to startle or distract
the operator which can cause an unsafe situation.
f Never touch the nylon cutting head when ever the
engine is running. If it is necessary to adjust the
protector or nylon cutting head, be sure to stop the
engine and confirm that the nylon cutting head has
stopped running.
f The engine should be turned off when the machine is
moved between work areas.
f In strt-up or during operation of the engine, never
touch hot parts such as the muffler, the high voltage
wire or the spark plug.
f After the engine has stopped, the muffler is still hot.
Never place the machine in any places where there
are flammable materials (dry grass, etc.), combustible
gasses or combustible liquids.
f Pay specials attention to operation in the rain or just
after the rain as the ground may be slippery.
f If you slip or fall to the ground or into a hole, release
the throttle lever immediately.
f Wear no-slip heavy duty work gloves to improve your
grip on the brush cutter handle. Gloves also reduce
the transmission of machine vibration to your hands.
f Always stop the engine and remove the spark plug
wire before making any adjustments or repairs except
for carburetor adjustments.
f Mix and store fuel in a container approved for
gasoline. Do not smoke while fueling or mixing fuel.
f Mix fuel outdoors where there are no sparks or flames.
Wipe up any fuel spillage. Move 30 ft. away from
refueling site before starting engine.
f Stop the engine and allow to cool before refueling or
storing the unit.
f Allow the engine to cool; empty the fuel tank and
secure the unit from moving before transporting
in a vehicle.

BEFORE USING

f Study this manual thoroughly.
f Familiarize yourself with the operation of the saw and
learn to use it properly.
f Never allow others (especially children) who have not
read the manual to use the machine.
f If the unit must be given to other people, give them as
this manual.
f Never remove the labels or security elements.
f Check that the fixing elements are stable and safety.
f Check the condition of the blade and the clamp.
Check that the cutting tools are not dull or damaged
their bindings. If necessary replace them. During this
check, turn off the engine and remove the spark plug
cap.
f Never operate the lawnmower when safety devices
are damaged or missing.
f Check the oil level before each mowing.
f Do not change the basic settings of the engine and do
not operate in overspeed.
f Check the ground and remove the lawn glasses,
stones, wood, plastic, scrap metal, branches and
other debris that may be thrown by the mower and
damage the cutting system.
WHEN USING
f Operate the mower only in daylight or good artificial
lighting
f The use of power equipment can be regulated.
Remember to comply with legal regulations which may
differ from one location to another.
ENGLISH • 25