Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: K24692
Wrenches: 3/4", 7/8"
Drill Bits: 1/2"
FRAME RAIL
j
BOLT – CARRIAGE 1/2-13 X 2.00 GR5
Qty. (4)
k
Qty. (1)
BLOCK - .25 X 1.50 X 4.00 *
l
NUT – 1/2-13
Qty. (1)
m
WASHER – FLAT 1/2"
Qty. (3)
n
WASHER – CONICAL 1/2"
Qty. (1)
1. RAISE HITCH INTO POSITION.
NOTE: THE DRIVER'S SIDE BRACKET IS POSITIONED INBOARD OF THE TIE DOWN HOOK, PASSENGER'S SIDE BRACKET IS POSISTIONED
OUTBOARD OF THE TIE DOWN HOOK.
NOTE: PLACEMENT OF THE BLOCK WITH 2 HOLES VARIES BY MODEL. SEE FIGURE 1.
2. INSTALL CARRIAGE BOLTS AND BLOCKS THRU VEHICLE TIE DOWN HOOKS AS SHOWN AND LOOSELY INSTALL FLAT WASHERS AND HEX
NUTS.
SEDAN MODEL:
3. FISHWIRE CARRIAGE BOLT AND BLOCK THRU END OF FRAME RAIL AND INTO EXISTING HOLE IN FRAME.
4. INSTALL REMAINING FASTENERS AS SHOWN.
HATCHBACK:
3. USING THE HITCH AS A TEMPLATE, DRILL 1/2" HOLE IN THE FORWARD MOST END OF SLOT IN SIDE BRACKET ON PASSENGER SIDE.
4. FISHWIRE CARRIAGE BOLT AND BLOCK THRU ACCESS HOLE ON THE BOTTOM OF FRAME RAIL.
5. INSTALL REMAINING FASTENERS AS SHOWN.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry
of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and
wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE
J684.
z
2006, 2007, 2015 Cequent Performance Products
Installation Instructions
FASCIA
FORD FOCUS 5 DR – ZX5 (HATCHBACK)
FORD FOCUS 3 DR – ZX3 (HATCHBACK)
Note: Does NOT fit models with Street Appearance Package
Drawbar must be used in the
RISE position only.
EXISTING HOLE ON SEDAN, DRILL 1/2" DIA.
HOLE ON HATCHBACK MODELS
ACCESS HOLE
(HATCHBACK)
SIDE BRACKET
s
m
r
j
Tighten all 1/2" fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
FORD FOCUS SEDAN,
Drawbar Kit:
3593
(Sold separately)
TIE DOWN HOOK
*(SEDAN)
m
s
k
p
j
o
Qty. (1)
p
Qty. (2)
q
Qty. (1)
r
Qty. (1)
s
Qty. (3)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908Kg) Max Gross Trailer Weight
200 LB (90.8Kg) Max Tongue Weight
Wiring Access Location: PC3, PC4 (SEDAN)
PC1, PC2 (HATCHBACK)
j
q n l
o
ALL MODELS REQUIRE
SPACER BETWEEN HITCH
AND FRAME
FIGURE 1
* POSITION OF THIS BLOCK
VARIES BY MODEL
BLOCK – .188 X 1.00 X 2.00
BLOCK - .25 X 1.50 X 2.00
BLOCK - .25 X 1.00 X 3.00
BLOCK - .25 X 1.00 X 2.00
NUT – LOCK 1/2-13
N24692
10-20-15
Part Numbers:
24692
77114
60870
*(HATCHBACK)
Rev. H
Publicidad
Manuales relacionados para Cequent Performance Products 24692
Resumen de contenidos para Cequent Performance Products 24692
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2006, 2007, 2015 Cequent Performance Products Sheet 1 of 3 N24692 10-20-15 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matiè re de sé curité des systè mes d’attelage. Feuille 2 de 3 N24692 10-20-15 Rev. H 2006, 2007, 2015 Cequent Performance Products...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684 2006, 2007, 2015 Cequent Performance Products Hoja 3 of 3 N24692 10-20-15 Rev.