Publicidad
INSTALLATION INSTRUCTIONS - ENGLISH
Before turning water on during either rough-in or
trim-out, ensure that the cartridge retainer clip is in
place. The cartridge and retainer clip were properly
installed and tested prior to leaving the factory. While
unlikely, it is possible that due to
handling the retainer clip may not
be properly installed. If the retainer
clip is not properly installed, water
pressure could force the cartridge
out of the casing causing personal
injury and/or water damage.
To Operate Shut-off Stops
This type is integral with casting, actuated by a 7/64 hex
wrench or needle nose pliers, requiring
a 90° turn to open or close. When the
flats on the head are vertical the stop is
closed; when horizontal the stop is open.
MAKE SURE ALL WATER
SUPPLIES ARE OFF.
Rough-In
UP
Install the casting with the
arrow pointing up
or the word "TOP" facing the ceiling. If the valve is
used for shower only, plug the bottom outlet. If
the valve is used for both a tub and shower, con-
nect the top outlet to the shower and the bottom
to the tub spout. Secure all pipes and the shower
ell and/or tub drop ell. Use Teflon® tape on all
threads.
Caution: This valve is equipped with
the Moen long-life POSI-TEMP cartridge
designed for smooth, trouble free operation.
When soldering do not heat valve any
higher than necessary. Overheating may dam-
age the cartridge or rubber stops. Following
this direction will allow you to solder without
removing the cartridge or rubber stops.
Warning: The cartridge and rubber stops MUST
BE REMOVED before brazing or resistance (elec-
tric) soldering.
Flushing
Important: Before closing wall openings,
pressure test valve and complete system using
flushing instructions.
Pipe chips, sand and other solids found in new and
renovated plumbing can damage the sealing sur-
faces of the cartridge causing leakage or spool
1
blockage. To avoid damage, DO NOT TURN ON
SUPPLY VALVES until instructed.
Make sure both hot and cold supplies are off.
Rotate cartridge stem until the notch flat points up
Clip
to relieve pressure and insure complete shut-off.
Remove the cartridge (see Disassembly). Slowly
turn on both hot and cold supplies and flush out
the body and lines. Close the hot and cold supplies
and replace cartridge (see Reassembly). Turn on
both supplies and check the system for leaks.
Cartridge Ears
If the balancing spool becomes stuck, apparent
during the trim-out test, the valve will only deliver
a trickle of water or will only deliver hot or cold
water. If this occurs, proceed as follows:
Make sure that both hot and cold service lines are
ON and ensure that the integral stops are open
(stop models). The valve will not operate unless
both supplies are on.
If the valve still does not function properly,
turn off both hot and cold supplies and remove
cartridge. The inner spool in the cartridge should
shake back and forth freely. If this does not hap-
pen, remove the stem assembly from the cartridge
sleeve, remove the cap from the assembly and
remove the balance spool. Carefully clean any for-
eign material from the balance spool and stem
assembly and reassemble. Caution: DO NOT
DAMAGE O-RINGS. If the spool still does not free
up, replace the entire cartridge.
ORIENT THE CLIP/BARS IN THE
SPOOL AND THE CAP FINGERS AS
SHOWN ABOVE
CAP
CLIP/BARS
BALANCE
SPOOL
Make sure the o-rings are free of foreign
material and are lubricated. Reassemble stem
assembly into cartridge sleeve. Reassemble
RETAINER
STOP TUBE
CLIP
CARTRIDGE
NOTCH
FRONT VIEW
TOP VIEW
HOT INLET
COLD INLET
FORWARD
TO REAR
INSTALL WITH
CARTRIDGE
STEM NOTCH
DOWN
CAUTION: CARTRIDGE MUST BE INSTALLED
WITH HOT & COLD INLETS AS SHOWN
CLIP/BARS
O-RINGS
STEM ASSEMBLY
TEMPERATURE
LIMIT STOP
KEY STOP
HANDLE
KNOB
KNOB
WASHER
SCREW
HANDLE
INSERT
PLUG BUTTON
LEVER
HANDLE
HANDLE
LEVER
SCREW
HANDLE
HANDLE
ADAPTER
CAP
SCREW
cartridge into valve (see Reassembly). Turn
on both water supplies. The valve should
function properly.
C.C
CLAMP
SCREW
C.C. SPOUT:
The Moen slip fit spout is designed with an
o-ring seal, specifically for installation with
copper water tube. Lookout must be free of burrs
inside and out. The edge must not be rolled. The
outside surface must be free from nicks and
scratches.
Press and twist the spout onto the lookout upside
down. Tighten clamp screw with a 5/32" hex
wrench until it starts to bind. Correctly position
spout against the wall and tighten by hand.
Further tightening with pliers or hex wrench is not
needed. Do not overtighten.
I.P.S.
IPS SPOUT:
CAUTION: This spout is ABS plastic and will crack
when in contact with some pipe thread com-
pounds. We recommend using Teflon® tape.
Screw tube spout onto pipe and tighten by hand.
If final turn by wrench is needed, use small wrench
with smooth jaws or pad wrench teeth with rag.
Pull outward to avoid scratching wall. DO NOT
INSERT TOOL INTO SPOUT END TO TURN SPOUT.
A
B
HANDLE
SCREW
PLUG BUTTON
TRADITIONAL
LEVER HANDLE
C
Slip-Fit
spouts
INS1542
Publicidad
