HIKOKI CG 36DB Instrucciones De Manejo página 13

STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains the
accessories listed on page 101.
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES
(sold separately) (Page 102)
Optional accessories are subject to change without notice.
APPLICATIONS
Trimming, scaling and mowing of weed.
BATTERY REMOVAL/INSTALLATION
1. Battery removal
Hold the housing tightly and push the battery latches to
remove the battery (see Fig. 3).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see
Fig. 3).
CHARGING
Battery and battery charger are not included with this
product.
For rechargeable batteries, please charge in according to
the handling instructions of the charger which you are using.
REMAINING BATTERY INDICATOR
You can check the battery's remaining capacity by pressing
the remaining battery indicator switch to light the indicator
lamp. (Fig. 4, Table 1)
The indicator will shut off approximately 3 seconds after the
remaining battery indicator switch is pressed.
It is best to use the remaining battery indicator as a
guide since there are slight diff erences such as ambient
temperature and the condition of the battery.
Also, the remaining battery indicator may vary from those
equipped to a tool or charger.
(Battery is not included, sold separately)
Table 1
State of lamp
Lights ;
The battery remaining power is over
75%
Lights ;
The battery remaining power is
50%–75%.
Lights ;
The battery remaining power is
25%–50%.
Lights ;
The battery remaining power is less
than 25%
Blinks ;
The battery remaining power is nearly
empty. Recharge the battery soonest
possible.
Battery Remaining Power
Blinks ;
Output suspended due to high
temperature. Remove the battery from
the tool and allow it to fully cool down.
Blinks ;
Output suspended due to failure or
malfunction. The problem may be the
battery so please contact your dealer.
As the remaining battery indicator shows somewhat
diff erently depending on ambient temperature and battery
characteristics, read it as a reference.
NOTE
Do not give a strong shock to the switch panel or break it.
It may lead to a trouble.
PRIOR TO OPERATION
CAUTION
Pull out battery before doing any assembly.
1. Installing the bike handlebars (Fig. 6) (CG36DB
only)
(1) Using the 4 mm hex wrench that is included, remove
the four bolts that have been temporarily secured to the
handle fi xture.
(2) Attach the handle right that has the lever and the handle
left, and then carefully secure the handle fi xture using
the four bolts.
To ensure the parts are attached securely, tighten the
bolts at least twice (repeating the following sequence).
Gradually increase the tightening torque each time to
ensure the bolts are tightened uniformly.
With four bolts: →
NOTE
Secure the handle left and handle right in a location that
provides a good grip.
CAUTION
Install the handle left and handle right properly and
securely as instructed in the handling instructions.
If not attached properly or securely, it may come off and
cause injury.
2. Installing the loop handle (Fig. 5) (CG36DB(L) only)
(1) Remove the M6 × 43 bolts (2 pcs.).
(2) Install the loop handle on the main pipe so that it leans
against the housing.
(3) Place the handle fi xture at the lower end of the main pipe
and secure it fi rmly using M6 × 43 bolts (2 pcs.) and M6
nuts (2 pcs.).
To ensure the parts are attached securely, tighten the
bolts at least twice (repeating the following sequence).
Gradually increase the tightening torque each time to
ensure the bolts are tightened uniformly.
With two bolts: →
NOTE
If your unit has handle location label on main pipe, follow
the illustration. (Fig. 5)
CAUTION
Install the loop handle properly and securely as
instructed in the handling instructions.
If not attached properly or securely, it may come off and
cause injury.
3. Installing guard (Fig. 7)
WARNING
Be sure to install the guard in its designated location.
Failure to heed this warning may result in injury from
fl ying stones.
NOTE
Use the supplied hex. bar wrench 4 mm for installation.
(1) Align the two holes in the cover bracket and the guard
and insert two M6 × 25 hex. socket button bolts. (The
cover bracket is installed in the gear case.)
13
English
→ → → → → →
→ → ····
····