Operational Cautions; Maintenance And Inspection - HIKOKI CG 36DB Instrucciones De Manejo

English

OPERATIONAL CAUTIONS

This tool incorporates a function to safeguard the electronic
components that control the main unit. If an overload occurs
during mowing—for example, if the nylon head locks up or
becomes clogged with vegetation—the function will activate
to stop the motor. If this happens, the power lamp will fl ash.
Check the lamp status and take appropriate corrective
action.
You can resume use after taking the following corrective
action. Take steps to reduce the load imposed on the
motor—for example, by reducing the cutting depth. Before
clearing vegetation from the nylon head, turn off the power
and remove the battery from the tool main unit.
Power switch
Power lamp
fl ashing status
The internal
temperature
exceeded the
preset limit. The
tool has stopped.
0.5 s on/0.5 s off (The motor turns
off . The power
(slow fl ashing) will shut down
automatically after
one minute.)
[Temperature
protection
function]
The tool
attachment load
exceeded the
preset limit. The
tool has stopped.
0.1 s on/0.1 s off
(The motor
turns off and the
(rapid fl ashing)
lamp fl ashes for
10 seconds.)
[Overload
protection
function]
NOTE
If the power lamp continues to fl ash even after the
corrective action has been taken, the tool may be
damaged or defective.
Please contact the retail outlet where you purchased the
tool for repairs.
Power lamp
Cause Corrective action
Turn off the power
and wait for the
device to cool.
You can
resume use
once the device
temperature has
fallen.
Turn off the power
and remove the
battery. Resolve
the cause of the
overload.
You can resume
use after resolving
the overload
cause.

MAINTENANCE AND INSPECTION

CAUTION
Pull out battery before doing any inspection or
maintenance.
1. Checking the condition of the nylon head
The nylon head should be checked regularly. If worn or
broken nylon head can slip or decrease the effi ciency of
the motor and burn it out.
Replace worn nylon head with new ones.
CAUTION
If you use a nylon head of which point is worn or broken,
it will be dangerous. So replace it with a new one.
2. Check the Screws
Loose screws are dangerous. Regularly inspect them
and make sure they are tight.
CAUTION
Using this power tool with loosened screws is extremely
dangerous.
3. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
4. Cleaning of the outside
When the grass trimmer is stained, wipe with a soft dry
cloth or a cloth moistened with soapy water. Do not use
chloric solvents, gasoline or paint thinner, as they melt
plastics.
5. Storage
Store grass trimmer in a place in which the temperature
is less than 40°C and out of reach of children.
NOTE
Storing Lithium-ion Batteries
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
signifi cantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, signifi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to fi ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
Important notice on the batteries for the HiKOKI
cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used with
batteries other than these designated by us, or when
the battery is disassembled and modifi ed (such as
disassembly and replacement of cells or other internal
parts).
16