Thermador VCK1 Instrucciones De Instalación página 2

DUCTING FOR VCK300
1. Use a transition (BSH #1255-17) when 7" round Duct is used.
2. Finish with roof jack (BSH #1255-6) or wall cap (BSH #1255-1). Make
sure all dampers are free to open.
IMPORTANT: Be sure the 3-1/4" x 10" knockout on the housing body is
REMOVED before attaching the damper collar*.
* Damper collar, two ventilator motor support bolts and nuts are shipped
with the blower (model# VCK300).
DUCTING FOR VTR600
To adapt this VCK-1 unit for installation with the VTR600 a transition (BSH
#1308-8) and an 8" round duct must be used. Before installing the VCK-
1 in hood or cabinet attach transition to top of VCK1 through holes with
screws provided.
IMPORTANT: Be sure the 8" x 13" knockout on the top of the housing
body is REMOVED before attaching the transition.
VCK1 with VCK300 (Integral Blower), OR VTR600 or VR1000 (Remote
Blower) these installations must meet all local code requirements .
1. Unless otherwise required by compliance with local codes, recommended
installation height from countertop to VCK1 mounting surface over
counter level range, cooktop, 30" to 34", over indoor barbecue 34" to
48".
2. Cut a 9-3/4" x 19" opening in the bottom of the cabinet or hood to allow
for the ventilator body (see figures 2 and 3 for minimum clearance).
Safety Warning: Turn off proper circuit at the service entrance and
lockout panel before wiring this unit.
Fig. 4
DUCTING FOR KITCHEN CABINET INSTALLATION
VCK300
1 2 3 1 2 1 2
1 2 3
1 2 3 1 2 1 2
1 2 3
1 2 3 1 2 1 2
Front
1 2 3
1 2 3 1 2 1 2
1 2 3
1 2 3 1 2
1 2 3 1 2 1 2 1 2
1 2 3 1 2
1 2 3 1 2
10-1/2"
VTR600
1 2 1 2
9-3/4" x 18-3/8"
1 2 1 2
Cutout
•
1 2 1 2
1 2 1 2
3/4" required
for Clearing
1 2
1 2 1 2
Collar for
1 2 1 2
Horizontal
1 2 3
Discharge
1 2 1 2 1 2 3
Absolute
Minimum
10-1/2"
Fig. 2
Fig. 3
Fig. 5
1 2 3
1 2 3
1 2 3
Transi-
1 2 3
tions:
1 2 3
1 2 3
For VR1000 -
1 2 3
#1308-10
1 2 3
1 2 3
For VTR600 -
1 2 3
1 2 3
1 2 3
1 2 3
1 2 3
VERTICAL
#1308-8
Absolute
Minimum
Page 2
DUCTING FOR VCK300
(For ventilator motor mounted inside of
ventilator housing)
1 2 1 2
1 2
1 2 1 2
*Damper Collar for
3-1/4" x 10" duct
1 2 1 2
Minimum Clear-
1 2 1 2
ance 1-3/8"
1 2 1 2
Minimum 3" Length
1 2 1 2
of 3-1/4" x 10"
1 2 1 2
Minimum Clear-
ance 3/4"
1 2 1 2
*To Bottom of
1 2 1 2
Damper Collar
1 2 3
1 2 3 1 2 1 2
1-1/4"
1 2 3
1 2 1 2
Recommended
1 2 1 2
Depth 4-1/4"
1 2 1 2
Minimum
DUCTING FOR THE VTR600
( Vertical Discharge only )
1 2 3
1 2 3 10" Diameter Duct for VR1000
1 2 3
8" Diameter Duct for VR600
1 2 3
1 2 3
(Duct NOT supplied)
1 2 3
1 2 3
1 2 3
Transitions:
1 2 3
1 2 3
For VR1000 - #1308-10
• 1 2 3
For VR600 - #1308-8
1 2 3
1 2 3
1 2 3
Transition Height 10-1/4"
1 2 3
1 2 3
Minimum Clearance 1-3/8"
1 2 3
1 2 3
1 2 3
1 2 3 4 5 1 2 3
Mounting Surface
1 2 3 4 5 1 2 3
1 2 3
1 2 3
1 2 3
Recommended
1 2 3
1 2 3
Depth 4-1/4"
1 2 3
1 2 3
Retainer Angle
Retainer Angle
Mounting Bolts
are installed in
rear position for
Horizontal
Discharge
Mounting Bolts
are installed in
forward position
Vertical
Discharge
HORIZONTAL
}
}