Product Description; Electrical Connections; Motor Connection; Power Supply - Stobag SRCR 100 A Manual Del Usuario

Warnings
The SRCR 100 A control unit is suitable for the control of a single-phase
asynchronous motor powered by the electrical mains and used for the
automation of awnings, rolling shutters and similar fixtures.

1) Product description

The SRCR 100 A control unit enables the control of a single-phase
asynchronous motor powered by the electrical mains, with "COM-
MON" "UP" "DOWN" type connections, and used for the automation
of awnings, rolling shutters and similar fixtures.
The control unit incorporates a radio receiver operating at a frequency
of 433.92 MHz, with rolling code technology that guarantees high
levels of security. Up to 30 transmitters ("SKIMY SRCH" fig. 1, "SKIMY
SRCW" fig. 2) or radio-controlled sensors ("SKIROSOL SRCK 610"
fig. 3) can be memorized for each control unit. After each command,
the motor is powered for the operating time required. An electric
limit switch incorporated in the motor stops the movement when the
desired position is reached. The programming can be done directly
from the transmitters, with beeps that sound to guide users through
the various phases. "SKIROSOL SRCK 610" climatic sensors (Fig. 3)
enable users to manage the movement of the awnings or rolling shut-
ters automatically, depending on the wind, sun or rain conditions.
2) Installation
!
The electrical systems and automations must be installed
by qualified and experienced personnel in compliance with
current legislation. Before you proceed to make any connec-
tions make sure that the power supply is disconnected.
1. Strip the motor cable and the power supply cable about 3 cm and
then the single wires approx. 5 mm.
2. Open the container by removing the "cable cap" as shown in
fig. 5.
3. Thread the two cables through the designated holes in the "cable
cap" (see fig. 6).
4. Pull the card a few centimetres out of the container (see fig. 7).

2.1) Electrical connections

!
Carefully follow all the connection instructions, if you have
any doubts do NOT make experiments but consult the relevant
technical specifications sheets which are also available on the
web site www.stobag.com
An incorrect connection may cause serious damage to the
control unit.
4

2.1.1) Motor connection

The single-phase asynchronous motor powered by the electrical
mains must be connected on terminals 1-2-3-4 (DOWN, COMMON,
UP, EARTH).
"DOWN" is controlled by the ▼ key on the remote control, and "UP"
by the ▲ key. (anemometer intervention direction).

2.1.2) Power supply

The main supply to the unit must be connected using the terminals 5-6-7 (earth, phase, neutral) as shown in Fig. 4
14
Any other use is improper and prohibited. The unit must be installed by
qualified technicians in compliance with the electrical and safety regula-
tions in force.
N.B. Besides "SKIMY SRCH", "SKIMY SRCW" and "SKIROSOL
SRCK 610", the control unit can manage other kinds of transmitters
and functioning modes, too. Please refer to Chapter 4 "Additional
information" for further explanations.
1 2
SKIMY SRCH SKIMY SRCW
5. Connect the wires to the terminals as shown in fig. 8, observing the
diagram in fig. 4 and the operations described in chapter 2.1.
6. Fold the cables as shown in fig. 9.
7. Push the card inside the container, make sure that the stripped
length of the cable is fully inside the container, then slide the "cap"
until the container closes completely (see fig. 10).
8. The control unit can be fitted directly in the shutter/awning box,
double-sided tape can be used for this. To avoid the risk of water
leaks it should be positioned with the cables towards the bottom
as shown in Fig. 11. Do not place it with the cables towards the
top (Fig. 12).
!
Do not perforate the container.
M
COM
L
N
If the rotation direction is not correct, invert the terminals 1 and 3.
!
do not connect more than one motor to each control unit.
3
SKIROSOL SRCK 610
4 3 2 1
5 6 7
www.stobag.com