Publicidad
Enlaces rápidos
Publicidad
Manuales relacionados para La-Z-Boy BELLAMY
Resumen de contenidos para La-Z-Boy BELLAMY
- Página 1 Diseñado para que sea cómodo, y fabricado para que siga siéndolo. Executive Chair Assembly Instructions Silla ejecutiva Instrucciones de Ensamblaje MODEL / MODELO 45783 Soporte m ximo á de la silla: BELLAMY 113 kg 250 lbs...
-
Página 2: Instrucciones De Ensamblaje
Chair Assembly Instructions Carefully unpack all parts and identify them against the parts list before attempting to assemble. To avoid scratching the components, assemble the chair on a protected surface. Note: The casters sold with this chair are intended for use on carpet and not recommended for use on tile or hard wood floors. Using these casters on tile or wood flooring may cause floor surface damage, so please consider purchasing a chairmat to protect your floor surfaces. - Página 3 PARTS/PARTES Casters Star Base Gas Lift with Telescoping Cover Seat Plate Ruedas Elevador neumático y cubierta Base en forma de estrella Mecanismo del asiento telescópica Quantity/cantidad: 5 Quantity/cantidad:1 Quantity/cantidad: 1 Quantity/cantidad: 1 Right Arm Left Arm Back Cushion Seat Cushion Cojín del respaldo Brazo derecho Brazo izquierdo...
- Página 4 Step 1 Place the Star Base (B) upside down and insert 5 Casters (A) into the holes on the Star Base (B). Paso 1 Ponga la base en forma de estrella (B) con las patas hacia arriba y inserte las 5 ruedas (A) en los hoyos situados en la base (B). Step 2 Turn the Star Base (B) over and insert the Gas Lift with Telescop- ing Cover (C) through the center hole on top of Star Base (B).
- Página 5 Step 3 Attach Seat Plate (D) to the bottom of the Seat Cushion (F) (with the front of the seat plate facing the front of seat cushion). Attach by using 1-3/4” Screws (J) for the front holes of the Seat Plate (D) and 1” Screws (I) for the rear holes of the Seat Plate (D) and tighten screws.
- Página 6 Step 4 Insert Levers (D1 & D2) of Seat Plate (D) to the pre-attached cable lever receivers on the underside of Seat Cushion (F) (with the front of the levers facing the front of seat cushion). Push down the key on the receivers to pull out the levers.
- Página 7 Step 5 Attach the Back Cushion (G) to the Seat Cushion (F) by positioning the back support plate over the Seat Plate (D) with1-1/4” Screws (K). *Note : Do not tighten the screws completely. Paso 5 Alinee el cojín del respaldo (G) con el cojín del asiento (F) por medio de colocar la placa de soporte del respaldo sobre la placa del asiento (D) con tornillos de 32mm (K).
- Página 8 Step 6 Insert 2-1/2” Screws (L) into arm holes, attaching Arms (E1 & E2) (with the front of arms facing the front of seat cushion) to sides of Seat Cushion (F) and Back Cushion (G). *Note : Tighten all the screws completely. Remember to tighten the back support plate screws.
- Página 9 Step 7 Put the Plastic Shroud (H) over the Seat Plate (D) (with the front of plastic shroud facing the front of seat cushion). Align shroud posts to holes on bottom of Seat Cushion (F) and press into position. Paso 7 Coloque la cubierta de plástico (H) sobre la plancha del asiento (D) (con la parte frontal de la cubierta de plástico mirando hacia el frente del...
- Página 10 Step 8 Position the assembled chair upright with the seat plate facing down. Insert the Gas Lift with Telescoping Cover (C) into the center hole of the Seat Plate (D). Paso 8 Coloque la silla ensamblada verticalmente, con la plancha del asiento hacia abajo. Inserte el elevador neumático con la cubierta telescópica (C) en el hoyo central de la mecanismo del asiento (D).
-
Página 11: Function Instruction
Operating Instructions Instrucciones de Uso Function Instruction - 1 To Adjust Seat Height : While seated, lean forward and reach under the right side of the chair to find the lever. Lift the lever and raise your body up slightly to allow the chair to rise to the desired height. - Página 12 Function Instruction - 2 To Operate Tilt Lockout : While seated, reach under the left side of the chair to find the lever. Push down the lever and lean back to allow the chair to tilt backwards. To lock the chair in the upright or vertical position, sit upright and pull the lever to the up position.
-
Página 13: Para Ajustar La Tensión Del Mecanismo De Inclinación
Function Instruction - 3 To Adjust Tension On The Tilt : Reach under the front center of the chair, grasp the round knob (R) and turn it counter- clockwise to stiffen the tilt mechanism for a heavier user. Turn the knob (R) clockwise to loosen the tilt mechanism for a lighter user. - Página 14 Limited Warranty True Innovations seating products are warranted against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as that party or entity which purchases True Innovations furniture from an authorized True Innovations retailer as shown by the original sales receipt.
-
Página 15: Garantía Limitada
Garantía Limitada Los productos de True Innovations seating están garantizados contra defectos de material y mano de obra mientras está en posesión de su “Comprador Original”. El término “Comprador Original” se define como el individuo o entidad que compra el mueble de True Innovations de un distribuidor autorizado así... - Página 16 LA-Z-BOY is a trademark of La-Z-Boy Incorporated and is used under license to LF Products Pte Ltd. LA-Z-BOY es una marca de La-Z-Boy Incorporated y es usada con licencia de LF Products Pte Ltd.