EINHELL EXPERT TE-CC 315 U Manual De Instrucciones Original página 28

Anleitung_TE_CC_315_U_SPK8__ 19.11.12 15:56 Seite 28
GB
Before you use the machine for the first time,
n
check that the voltage marked on the rating plate
is the same as your mains voltage.
If you need to use an extension cable, make sure
n
its conductor cross-section is big enough for the
sawʼs power consumption. Minimum cross-
section: 1 mm 2 .
If you use a cable reel, the complete cable must
n
be pulled off the reel.
Check the power cable. Never use a faulty or
n
damaged power cable.
Operators have to be at least 18 years of age.
n
Trainees of at least 16 years of age are allowed
to use the machine under supervision.
Keep your workplace clean of wood scrap and
n
any unnecessary objects.
Persons working on the machine should not be
n
distracted.
Note the direction of rotation of the motor and
n
saw blade.
After you have switched off the motor, never
n
slow down the saw blade by applying pressure to
its side.
Only fit blades which are well sharpened and
n
have no cracks or deformations.
Never dismantle the machineʼs safety devices or
n
render them inoperative.
Faulty saw blades must be replaced
n
immediately.
Never use saw blades which do not comply with
n
the data specified in this manual.
It is imperative to make sure that all devices
n
which cover the saw blade are in good working
order.
Important: It is prohibited to use this saw to
n
make plunge cuts.
Damaged or faulty safety devices have to be
n
replaced immediately.
The splitter is an important safety device. Not
n
only does it guide the workpiece, it also prevents
the kerf closing behind the blade so that there is
no kickback from the workpiece. Note the
thickness of the splitter. The splitter should never
be thinner than the saw blade body or thicker
than the width of its kerf.
The guard hood has to be lowered over the
n
workpiece for each cut.
Be sure to use a push stick when slitting narrow
n
workpieces (smaller than 120 mm in width).
Never cut workpieces which are too small to hold
n
securely in your hand.
It is imperative for the parallel stop to be clamped
n
on the right-hand side of the blade whenever you
cut narrow workpieces to size.
Always stand to the side of the saw blade when
n
working with the saw.
28
Never load the machine so much that it cuts out.
n
Always press the workpiece firmly against the
n
saw table.
Make sure that off-cuts do not catch on the saw
n
blade crown. Risk of catapulting!
Refit all guards and safety devices immediately
n
after you have completed any repairs or
maintenance work.
Be sure to observe the safety information and
n
operating and maintenance instructions issued
by the manufacturer, as well as the dimensions
listed in the Technical Data.
It is imperative to observe the accident
n
prevention regulations in force in your area as
well as all other generally recognized rules of
safety.
Note the information published by your
n
professional associations.
Connect up the dust extraction system on all
n
jobs. The operator has to be informed about the
conditions with an influence on dust
development, e.g. the type of material being
processed (source and collection of the dust),
the significance of local separation
arrangements, and the correct setting of hoods,
baffle plates and guides.
Operate the saw only with a suitable vacuum
n
extraction system or a standard industrial
vacuum cleaner.
Never remove loose splinters, chips or jammed
n
pieces of wood when the saw blade is running.
To rectify faults or remove jammed pieces of
n
wood, always switch off the machine first. Pull
the power plug!
If the sawing gap is worn, replace the table
n
insert. Pull the power plug!
This electric tool complies with the pertinent
n
safety regulations.
Keep your work area clean and tidy.
n
Untidy and unlit work areas can result in
accidents.
Keep the tool out of the rain and away from
n
moisture.
The ingress of water into an electric tool
increases the risk of an electric shock.
Be careful, watch what you are doing and use an
n
electric tool sensibly. Do not use the tool if you
are tired or under the influence of drugs, alcohol
or medication.
A moment of inattention when using the electric
tool can result in serious injuries.
Do not use an electric tool with a defective
n
switch. An electric tool that cannot be switched
on or off is dangerous and must be repaired.
Keep unused electric tools out of the reach of
n
children. Do not allow people who are not