English - Braun Satin-Hair Colour SPI-C 2000 DF Manual De Instrucciones

English

Our products are engineered to meet the highest
standards of quality, functionality and design.
We hope you thoroughly enjoy your new Braun
appliance. Carefully read the use instructions before
use.
Important
• Plug your hairdryer into an alternating current ( )
outlet only and be sure that your household
voltage corresponds to the voltage marked on the
hairdryer.
• This appliance must never be used near
water (e.g. a filled wash basin, bathtub
or shower). Do not allow the appliance to
become wet.
• When using the hairdryer in a bathroom, always
unplug it after use. Even a switched-off hairdryer
presents a hazard if not unplugged.
• For additional protection, it is advisable to install a
residual current device (RCD) with a rated residual
operating current not exceeding 30 mA in the
electrical circuit of your bathroom. Ask your
installer for advice.
• Care should be taken not to block the inlet and
outlet grill when the hairdryer is switched on.
If either grill becomes blocked, the hairdryer will
automatically cut out. After cooling for a few
minutes, it will switch back on automatically.
• Do not wrap the mains cord around the appliance.
Regularly check the mains cord for wear or
damage, particularly where it enters the product
and the plug. If you have any doubt about its
condition take the appliance to your nearest
Braun Service Centre for checking/repair. The
mains cord of the appliance may only be replaced
by an authorised Braun Service Centre.
Unqualified repair work can lead to extreme
hazards for the user.
• This appliance is not intended for use by children
or persons with reduced physical or mental
capabilities, unless they are given supervision by
a person responsible for their safety. In general,
we recommend that you keep the appliance out of
reach of children.
Description
1 Switch
2 Colour Saver button with light
3 Cold shot button
4 Protection filter
5 Colour Saver nozzle
6 Concentrator nozzle
7 Diffuser attachment (only with SPI-C 2000 DF)
6
Switch
(1)
Two airflow and three temperature settings allow you
to personalize your hairdryer for a fast and efficient,
but also gentle drying.
Airflow Temperature
2 high high
1 low medium
0 off low
Colour Saver Technology
Colour Saver Technology with satin ions maintains
the precious health of coloured hair as it protects the
hair from dry out and damage and prevents moisture
loss of coloured hair while drying. For beautiful
coloured hair that looks more healthy and vibrant for
longer.
Colour Saver button
By sliding up the Colour Saver button (2) you can
set a controlled limit to the maximum heat output of
your hair dryer, regardless of the airflow setting. As
a result, Satin Hair Colour Dryer prevents coloured
hair from overheating, excess dry out and damage
while still providing you with a powerful airflow.
The light shines when the Colour Saver function is
activated (a).
Colour Saver nozzle
The Colour Saver nozzle (5) blends cooler ambient
air with the dryer airflow. This new and increased
airflow blows a gentle breeze across a larger drying
area. For fast, yet most gentle drying.
Cold shot
(3)
To fix a style with cold air, press and hold the cold
shot button.
Protection filter
Regularly wipe the filter clean. For a thorough
cleaning, remove the filter and clean it under running
water.
Concentrator nozzle
For precise styling use the concentrator nozzle.
Volume diffusor
(only with SPI-C 2000 DF)
Attaching the diffusor (b)
• Align the notches on the rim of the diffusor
attachment with the slots in the hair dryer.
• Push the attachment onto the hairdryer, then turn
clockwise until the bayonet lock clicks into place.
• To remove the diffusor, turn in the opposite
direction and pull.
3
2
1
(4)
(6)
(7)