Technical Parameters; Indication Led - Elko EP iNels JA3-018M Guia De Inicio Rapido

Technical parameters

Outputs
Output:
Switched voltage:
Switched output:
Peak current:
Output relays separated
from all internal circuits:
Isolation between relay out-
puts GATE1, GATE2 and GATE3:
Isolates. voltage open
relay contact:
Minimal switched current:
Switching frequency without
load:
Switching frequency with
rated load:
Mechanical life:
Electrical life AC1:
Output indication:
Communication
Installation BUS:
Status indication unit:
Power supply
Supply voltage by BUS /
tolerance / nominal current:
Supply voltage of power
section (relay) / tolerance /
nominal current:
Dissipated power:
Connection
Terminal:
Operating conditions
Operating temperature:
Storing temperature:
Protection degree:
Overvoltage category:
Pollution degree:
Operating position:
Installation:
Design:
Dimensions and weight
Dimensions:
Weight:
TECHNICAL SUPPORT | E-mail: support@inels.com | Mobil: +420 778 427 366 | Tel.: +420 573 514 276, +420 573 514 211 | Fax: +420 573 514 227 | www.inels.com
Made in Czech Republic
JA3-018M JA3-018M/120V
9x changeover 4 A/AC15
250 V AC, 24 V DC
1000 W/AC15, 100 W/DC
10 A
basic insulated.
(Cat. III surges by EN 60664-1)
basic insulated.
(Cat. II surges by EN 60664-1)
1 kV
100 mA / 10 V DC
300 min -1
15 min -1
7
1x 10
1x 10 5
9x yellow LED
BUS
green LED RUN
27V DC, -20 / +10 %, 5mA
AC 230V (50 Hz), AC 120V (60 Hz),
-15 / +10 %, 20 mA -15 / +10 %, 40 mA
max. 2 W
2 2
max. 2.5 mm /1.5 mm with sleeve
-20 to +55 °C
-30 to +70 °C
IP20 device, IP40 mounting in the switchboard
II.
2
any
switchboard on DIN rail EN 60715
6-MODULE
90 x 105 x 65 mm
346 g
ELKO EP, s.r.o. | Palackého 493 | 769 01 Holešov, Všetuly | Czech republic | e-mail: elko@elkoep.com

Indication LED

Flashing interval of the respective LED when the maximum number of contacts is exceeded when
the relay is switched on:
Flashing interval of the respective LED when the max. Number of contacts is exceeded when the
relay is switched off :
Flashing interval of all LEDs in case of power failure with relay on:
Flashing interval of all LEDs in case of power failure with relay off :
Warning
Before the device is installed and operated, read this instruction manual carefully and with full
understanding and Installation Guide System iNELS3. The instruction manual is designated for
mounting the device and for the user of such device. It has to be attached to electro-installation
documentation. The instruction manual can be also found on a web site www.inels.com. Attention,
danger of injury by electrical current! Mounting and connection can be done only by a professional
with an adequate electrical qualifi cation, and all has to be done while observing valid regulations.
Do not touch parts of the device that are energized. Danger of life-threat! While mounting,
servicing, executing any changes, and repairing it is essential to observe safety regulations, norms,
directives and special regulations for working with electrical equipment. Before you start working
with the device, it is essential to have all wires, connected parts, and terminals de-energized. This
instruction manual contains only general directions which need to be applied in a particular
installation. In the course of inspections and maintenance, always check (while de-energized) if
terminals are tightened.
2/2