General Information; Technical Specifications - Michelin Wonder SPA SUPERDAINU Manual De Instrucciones

INFLATOR GAUGE

gENERAl INfoRMAtIoN

SUPERDAINU ® inflator gauge is designed, manufactured and certified
in Italy using advanced technology. It complies with the European
directive 86/217/EEC
Wonder carefully checks the origin and quality of all materials and
components used in production to offer its customers high quality
products that are guaranteed and also to reduce the impact on the
environment to a minimum. Our quality systems are ISO 9001 and
ISO 14001 certified. You are invited to observe the local laws and
regulations regarding this product to prevent accident or injury and
also control the general safety regulations for the use of this product.
Wonder denies any liability for any errors in measurement or damage
that could be caused by the following: incorrect or inappropriate use
of this product or any of its single components; not following the
instructions provided in this manual; use by unqualified individuals;
unauthorized modifications or alterations to this product.
This device is designed for intended use only, i.e. measurement,
inflation and regulation of internal pressure of motor vehicles tyres.
Any other use is considered inappropriate.
Model with Pe (bar) scale
2
gENERAl WARNINgS
• During inflation, maintain a safe distance to avoid injury due to accidental
bursting of the tyre.
• Never block the handle in the inflating position as this would result in a continuous
flow of air into the tyre that would produce a high risk of the tyre exploding.
• Check that the pressure from the compressor is higher than the pressure
recommended by the tyre manufacturer.
• Ensure that the air or nitrogen from the compressor passes through a separator
filter to prevent liquids (e.g. hydrocarbons) or other impurities from entering into
the inflator gauge causing oxidation of the internal components and damaging
the system of measurement.
• Constant or prolonged use when the instrument is under pressure using
pressured air or nitrogen can, in the course of time, alter the variables of the
measurement system producing an incorrect reading on the dial. It is therefore
recommended that the instrument is not left in use for long periods.
• SUPERDAINU ® inflator gauge is tested to resist levels of pressure up to
12.5 bar/181 psi/1,250 kPa only for short periods of time. In order to always
guarantee precise measurements and retain the calibration for the maximum
amount of time, it is recommended that the limit indicated above is respected.
• To obtain best results, the operating temperature should be between 15� and
25�C.
• Avoid knocks to the inflator gauge — do not disassemble.
SUPERDAINU
WONDER SPA
2 and the regulation UNI EN 12645:2014.
10
INFLATOR GAUGE
®
• Do not expose to bad weather conditions or direct sunlight and avoid sudden
changes in temperature.
• Do not submerge in water or detergents. Clean the instrument using a damp cloth.
• Do not use for inflation or checking pressure of tyres containing water ballast
or anti-puncture products.
• Avoid contact with solvents or hydrocarbons.
• Periodically check that the filter near the inlet of air from the compressor is in
correct working order.
• Keep the product, its accessories and any packing materials out of reach of
children.
• The disposal of this product must conform to the local regulations in force to
respect the environment and correct waste disposal.
• Do not attempt to inflate the tyre if the gauge is not connected to a compressor
or other source of air or nitrogen as this will cause the tyre to deflate.
• It is recommended to use original Wonder accessories.
Wonder carries out repairs to this product up to 5 years from the production
date.
Wonder will not accept instruments for repair or checks if any pieces are missing
or any attempt has been made to modify or disassemble them.
ACCESSoRIES
- Spare hose (150 cm) n. 1961 for standard valves
Measurement range
Instrument resolution: 0.1 bar | 1.45 psi | 10 kPa
operating temperature: -10�C — +40�C
Performance conforms to E.D. 86/217/EEC and norm UNI EN 12645:2014
Maximum airflow: 66 m
Maximum air source pressure: 15 bar | 218 psi | 1,500 kPa
3 The black square placed on the dial before the beginning of the scale indicates the resting
position of the pointer. It has illustrative purposes only and can not be used for calibration.
Changes in position of the pointer with respect to this reference do not imply an incorrect
calibration.
SUPERDAINU

TECHNICAL SPECIFICATIONS

: 0.7 — 10 bar | 10 — 145 psi | 70 — 1,000 kPa
3
/h at 10 bar | 145 psi | 1,000 kPa
3
11
®
WONDER SPA