Litex Industries UCI-WALL Instrucciones De Operación Y Instalación

There are four buttons (High, Med, Low, Off) to control the fan speed and one button (L1) to control the light.
I. SAFETY PRECAUTIONS
A.
DANGER: HIGH VOLTAGE! Household electrical power can cause serious injury or death. Disconnect source of electrical power to the ceiling
fan by removing fuse or switching off circuit breaker. Make sure all electrical connections comply with local codes, ordinances, the National Electrical Code,
and ANSI/NFPA 70-1999. If you are unfamiliar with electrical wiring, please use a qualified and licensed electrician.
B.
WARNING: To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with the remote control
receiver are designed to accept only one 12 gauge house wire and no more than two lead wires from the receiver. If your
house wire is larger than 12 gauge or there is more than one house wire to connect to the two receiver wires, consult an
electrician for the proper size wire connectors to use.
CAUTION:
C. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THE FAN WITH ANY
SOLID STATE SPEED CONTROL DEVICE OR CONTROL FAN SPEED WITH A FULL RANGE DIMMER SWITCH.
D. Do not use this wall control with solid state ceiling fans.
Electrical source and fan must be 120 volts, 60 Hz.
Maximum fan motor amps: 1.5; Maximum light watts: 300 incandescent
II. INSTALLATION OF RECEIVER (Please refer to Figure 1 before continuing.)
Manually set fan speed control to HIGH via pull chain and set light to ON via pull chain.
A.
IMPORTANT:
Fan speed and light control will not be activated by wall control if pull chains
for fan and light are not set to the HIGH and ON positions, respectively.
B. Disconnect source of electrical power to the ceiling fan by removing fuse or switching off
circuit breaker.
C. Lower ceiling fan canopy from the mounting bracket.
D. Disconnect existing wiring between ceiling fan and supply at electrical outlet box.
E. Lay the black antenna wire on top of the receiver and slide the receiver into the mounting
bracket. (Figure 1)
F. Using the wire connectors supplied, make wiring connections as follows: (Figure 2)
CONNECT:
GREEN fan wire.....................................................BARE supply wire
BLACK receiver wire (AC IN L)..............................BLACK supply wire
WHITE receiver wire (AC IN N)..............................WHITE supply wire
WHITE receiver wire (TO MOTOR N).....................WHITE fan wire
BLACK receiver wire (TO MOTOR L).....................BLACK fan wire
BLUE receiver wire (FOR LIGHT)...........................BLUE light wire (from fan)
Wrap each wire connector separately with electrical tape as an extra safety measure.
If other fan or supply wires are different colors than those mentioned,
have this unit installed by a qualified electrician.
G. Push all connected wires up into outlet box. Make sure antenna rests outside of mounting bracket.
H. Re-install the canopy on the mounting bracket.
III. INSTALLING WALL CONTROL
Remove wall plate from existing wall switch. Disconnect and remove the toggle switch from wall outlet
box. Using the wire connectors provided, make the electrical connections to the wall control as shown
in Figure 2. Wrap each wire connector separately with electrical tape as an extra safety measure.
Carefully push all connected wires back inside wall outlet box. Secure wall control with 2 screws provided.
Attach wall plate cover with the 2 original screws.
IV. AUTOMATED LEARNING PROCESS
CAUTION: The wall control can be programmed to multiple receivers or fans. If this is not desired,
turn power off to any other programmable receiver or fan.
A. Remove faceplate to reveal battery compartment and dimmer switch.
B. Setting the dimmer switch:
Locate the dimmer switch above the battery compartment labeled "DIM" and "ON". Set dimmer switch to ON (DIM) position only if using incandescent bulbs.
Set dimmer switch to OFF (ON) position if using LED or compact fluorescent bulbs. (Figure 4) NOTE: Most LED or compact fluorescent bulbs are not
compatible for use with dimmer controls.
C. Install 12-volt battery (included) IMPORTANT: Wall control will not function unless battery is installed.
D. Restore electrical power, set slider switch on wall control to the ON position.Within 30 seconds of turning on the wall control, press the "OFF" button, located on
the wall control, for 5 seconds or until light on fan blinks twice. Test the light and fan functions to confirm the programming (learning process) is complete.
E. Replace faceplate on wall control. (Figure 4)
V. WALL CONTROL--CARE AND OPERATION
A. If you find that your fan and light kit go on and off without using your wall control, turn power off and repeat Section IV
(Automated Learning Process) above.
B. To prevent damage to wall control, remove the battery if not used for long periods of time.
C. Operation buttons on the front panel of the wall control:
HIGH button for fan HIGH speed
MED button for fan MEDIUM speed
LOW button for fan LOW speed
OFF button for fan speed OFF
L1 button for light BRIGHTNESS and OFF
The light function is controlled by pressing the L1 button. Hold button down to increase or
decrease light. Tap button quickly to turn light off or on. If you press the button in excess of
0.7 seconds it becomes a dimmer. The light varies cyclically in 0.8 seconds. The light button
has auto resume, so the light will stay at the same brightness as the last time it was turned off.
VI. TROUBLESHOOTING GUIDE
A. Remote control fails to operate:
1. Make sure there is power to the receiver.
2. Make sure the receiver is wired correctly.
3. Make sure that the fan is set on the highest speed via pull chain.
4. Make sure the light kit is turned on via pull chain.
5. Make sure the battery in the wall control is good.
6. The learning process between fan and wall control may not have been successful.
Turn power off and repeat Section V (Automated Learning Process).
B. Transmitter won't operate at distance:
If transmitter operates fan and light kit when up close but not at 40 feet away, try
placing the black antenna wire higher and make sure the black antenna wire is visible.
NOLI1502
GENERAL INFORMATION
This wall control is designed to separately control your ceiling fan speed and light brightness.
The red indicator on the transmitter will light when any button is pressed.
INSTALLATION AND OPERATING INSTRUCTIONS
Electronic ballast (LED lights or CFL lights) 300VA
TO:
20˚
19˚
CAUTION: FOR MOUNTING RECEIVER,
CEILING ANGLE SHALL NOT EXCEED
19 DEGREES; RECEIVER MODEL: UC7067RYA
AC SUPPLY
BLACK
BLACK
GREEN
BLACK
BLACK
BLACK
WALL
CONTROL
RECEIVER
WALL CONTROL
DIM ON
DIMMER
SWITCH
Fig. 4
CAUTION:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
USE THE FAN WITH ANY SOLID STATE SPEED CONTROL DEVICE
OR CONTROL FAN SPEED WITH A FULL RANGE DIMMER SWITCH.
FOR CUSTOMER SERVICE CALL: 1-800-486-4892
MODEL: UCI-WALL
MOUNTING
BRACKET
and
above
RECEIVER
DOWNROD
Fig. 1
WHITE
ANTENNA
RECEIVER
BLUE BLUE
BLACK
BLACK
WHITE WHITE
BARE
GREEN
CANOPY
Fig. 2
CAUTION: DO NOT USE
FAN SPEED CONTROL
IN CANOPIES WHERE
THE MOUNTING IS NOT
AS SHOWN IN FIGURE 3
OF THE INSTALLATION
INSTRUCTIONS
Fig. 3
-
1 1
AND PLATE
DIM ON
FACEPLATE
BATTERY
LITEX INDUSTRIES, LTD.
GRAND PRAIRIE, TX 75050