Publicidad
Enlaces rápidos
Publicidad
Manuales relacionados para DHP 3137096
Resumen de contenidos para DHP 3137096
- Página 1 Weight Limits: 150 Lbs 68 Kgs 150 Lbs 68 Kgs...
- Página 3 RIGHT FRAME CAP LEFT FRAME LEG 01 T902630 T902640 QTY: 1 LEG 02 T902620 QTY: 1 T902650 QTY: 1 QTY: 1 GUARD RAIL LEG 03 FRONT SIDE T902420 T902660 RAIL QTY: 2 QTY: 2 T902670 QTY: 1 NOTE: PARTS , & HAVE PROTECTIVE END CAPS PRE-INSTALLED 3 21 B34313709600...
- Página 4 BACK SIDE RAIL MESH RAILS MESH BRACE LEFT END T902570 T902680 T902690 PLATE QTY: 1 QTY: 2 QTY: 2 T902700 QTY: 1 RIGHT END PLATE T902705 QTY: 1 4 21 B34313709600...
- Página 5 HOOK RETAINER HARDWARE NOTE: T902140 Please do not completely tighten any screws until the T902750 CENTER LEG entire assembly is complete. QTY: 3 QTY: 2 T902740 Once assembly is complete, please be sure tighten all QTY: 1 hardware LEFT MECHANISM(1) T901340 RIGHT MECHANISM(1) T901350...
- Página 6 CURVED BOLT WASHER 1/4-20 x 16mm BOLT T208440 T124790 1/4-20 x 30mm QTY: 24 BOLT QTY: 18 T125410 1/4-20 x 35mm BOLT QTY: 5 T125510 1/4-20 x 40mm QTY: 8 A19710 QTY: 6 BOLT 1/4-20 x 75mm A19700 QTY: 8 RUBBER LOCK NUT WASHER...
- Página 7 * ALWAYS USE THE RECOMMENDED SIZE MATTRESS OR MATTRESS SUPPORT, OR BOTH, TO HELP PREVENT THE LIKELIHOOD OF ENTRAPMENT OR FALLS. * TO PREVENT INJURY, DHP RECOMMENDS ONE TWIN SIZE MATTRESS AND ONE FULL SIZE MATTRESS TO BE USED. * USE ONLY A TWIN MATTRESS WHICH IS 74"-75" LONG AND 37 1/2"-38 1/2" WIDE ON UPPER BUNK AND A FULL MATTRESS WHICH IS 74"-75" LONG AND 53 1/2"-54 1/2"...
- Página 8 Attach the END PLATE (K) to the LEGS (C & E) with the WASHERS (6) and BOLTS (1) as shown. Attach the LADDER (N) to the LEG (C) with the WASHERS (6) and BOLTS (5) as shown. Hardware Required 8 21 B34313709600...
- Página 9 Attach the END PLATE (U) to the LEGS (D & E) with the WASHERS (6) and BOLTS (1) as shown. Attach the LADDER (N) to the LEG (D) with the WASHERS (6) and BOLTS (5) as shown. Hardware Required 9 21 B34313709600...
- Página 10 Attach the RIGHT FRAME CAP (A) to the LEGS (C & E) with the WASHERS (6) and BOLTS (5). Attach the LADDER (N) to the RIGHT FRAME CAP (A) with the WASHER (6) and BOLT (2) as shown below. Hardware Required 10 21 B34313709600...
- Página 11 Attach the LEFT FRAME CAP (B) to the LEGS (D & E) with the WASHERS (6) and BOLTS (5). Attach the LADDER (N) to the LEFT FRAME CAP (B) with the WASHERS (6) and BOLTS (2) as shown below. Hardware Required 11 21 B34313709600...
- Página 12 Lay the MESH BRACES (J) into the GUARD RAILS (F) and slide the MESH (L) into the GUARD RAILS (F) as shown below. Be careful not to pinch your fingers as noted below. Hardware Required NOTE: Be careful when slide MESH into place not to let you finger get pinched by the MESH BRACES! NOTA: ¡Tenga cuidado cuando el ACOPLAMIENTO de la diapositiva en lugar no le dejó...
- Página 13 Slide the MESH RAILS (I) through the GUARD RAIL (F) and lock in to place with the WASHERS (7) and BOLTS (5) as shown below. Hardware Required 13 21 B34313709600...
- Página 14 With the help of another person, attach the GUARD RAILS (F) to the FRAME CAPS (A & B) with the WASHERS (6 & 12) and BOLTS (2) as shown. Attach the FRONT and REAR RAILS (G & H) to the LEGS (C, D & E) with the WASHERS (6) and BOLTS (5) as shown.
- Página 15 Attach the LEFT and RIGHT MECHANISMS (S & T) to the END PLATES (K & U) with the BOLTS (4) and NUTS (8) as shown. Attach the CENTER LEG (P) to the FRONT RAIL (G) with the BOLT (4) and NUT (8) as shown. Appy the ADHESIVE PADS (11) to the RAILS (G &...
- Página 16 Attach the FUTON MESHES (M) to the LEFT and RIGHT MECHANISMS (S & T) with the BOLTS (3) and NUTS (8) as shown below. Hardware Required 16 21 B34313709600...
- Página 17 Attach the HOOKS (R) and RETAINERS (Q) into place as shown below. 17 21 B34313709600...
- Página 18 B34313709600 Limites Del Peso: 150Lbs\68Kgs (TAPA) - 300 Lbs\136Kgs (FONDO) REGRESAS ESTA PRODUCTO A LA TIENDA ALTO Las tiendas no tiene partes. Si falta partes o las partes esten danados llame gratis a la servicio del cliente. Con gusto mandarnos las partes. Sin alguno carga. Nesacitas partes o Asistancia? o visitar la pagina del internet www.dhpfurniture.com Para servicio mas rapido y reliable por favor tenga esta manual listo.
- Página 19 CAÍDAS. * PARA PREVENIR LESIÓN, DHP RECOMIENDA UN COLCHÓN GEMELO DEL TAMAÑO Y UN COLCHÓN DEL MISMO TAMAÑO QUE SE UTILIZARÁN. * UTILICE SOLAMENTE Un COLCHÓN GEMELO QUE SEA 74"-75" DESEE Y DESEEN 37 1/2"-38 El 1/2" DE PAR EN PAR EN La CUCHETA SUPERIOR Y Un COLCHÓN LLENO QUE SEA 74"-75"...
- Página 20 PAGE 08 Una la PLACA DE EXTREMO (K) a las PIERNAS (C y E) con las ARANDELAS (6) y los PERNOS (1) según lo demostrado. Una la ESCALA (N) a la PIERNA (C) con las ARANDELAS (6) y los PERNOS (5) según lo demostrado PAGE 09 Una la PLACA DE EXTREMO (U) a las PIERNAS (D y E) con las ARANDELAS (6) y los PERNOS (1) según lo demostrado.