Descargar
Compartir
Imprimir esta página
  1. Manuales
  2. Marcas
  3. Rola Manuales
  4. Accesorios de Automóviles
  5. 59403
  6. Manual de instrucciones

Rola 59403 Manual De Instrucciones

Ocultar thumbs Ver también para 59403:
1
2
3
4
5
6
7
8
9

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Descargar este manual
Please read all instructions carefully before assembly, installation and/or use of this product.
ASSEMBLY INSTRUCTIONS:
The shank for your (3) place bike carrier is pre-assembled to be used with a 2" hitch.
For use with a 2" hitch:
1.
Tighten both hex bolts to 75 ft-lb to secure the shank to the Collar Bracket. (See Diagram 1)
For use with a 1-1/4" hitch:
1.
Remove the two hex bolts holding shank to collar bracket.
2.
Remove the two spacer plates. The spacer plates are not required for the 1-1/4" hitch application.
3.
Insert the 2" square end of shank into collar bracket. Line up the two ½" diameter holes in shank with the two holes
in collar bracket. Re-Install the two ½" bolts and tighten bolts to 75 ft-lb.
(See Diagram 2)
To attach Main Support tube to collar bracket:
1.
Use key to unlock lock on Collar Bracket.
2.
Pull spring loaded release pin on side of Main Support tube,
remove handle mechanism, and rotate bike Support Arms
into the UP position. Re-insert the handle mechanism. Pull
out the spring loaded release pin and push handle all the
way down. Let the spring loaded pin go so that it fully
engages the handle mechanism.
3.
Attach Main Support tube to Collar Bracket in orientation
shown (see Diagram 3). Line up the hole near end of main
support tube with the slotted hole in collar bracket and install
one (1) ½" x 3-1/4" lg. hex bolt, two (2) nylon flat washers,
and locknut as shown. Tighten locknut until it is snug
against the flat washers.
4.
Lock Collar Bracket to Main Support tube so bike carrier is
in the upright position.
Collar Bracket
Lock
2" Shank
5/8" Hole
½" x 3" Hex Bolt
Locknut
(2) Places
Tighten Bolts
Diagram 1
Cequent Towing Products - Plymouth, MI
Technical Service: (888) 521-0510
Product Name:
Do not use first hole to secure bike
Rack to hitch.
1-1/4" Shank
Hitch pin
hole
½" Holes
½" x 3" Hex Bolt
Locknut
(2) Places
Tighten Bolts
Diagram 2
3 Place Bike Carrier - Folding
Product Code:
59403
"Slotted"
Hole
www.rolaproducts.com
Handle Mechanism
Drop of Oil
Release
Pin
Main Support
Tube
Collar
Bracket
½" x 3-1/4" Hex Bolt
(2) Nylon Flat Washer
Locknut
Diagram 3
59403N Rev B
9-29-06

Publicidad

loading

Manuales relacionados para Rola 59403

Resumen de contenidos para Rola 59403

  • Página 1 3 Place Bike Carrier - Folding Product Name: Product Code: 59403 Please read all instructions carefully before assembly, installation and/or use of this product. ASSEMBLY INSTRUCTIONS: The shank for your (3) place bike carrier is pre-assembled to be used with a 2” hitch.
  • Página 2 3 Place Bike Carrier - Folding Product Name: Product Code: 59403 Please read all instructions carefully before assembly, installation and/or use of this product. LOADING INSTRUCTIONS: Place the bike rack receiver into your receiver hitch. Fit rack as close to vehicle as possible.
  • Página 3 (as a result of colliding with or trying to avoid fallen bicycles and/or the rack). • ROLA™ racks are powder coated to help prevent rust. As with any metal equipment it is recommended that you keep the rack clean and remove road salt and debris.
  • Página 4 Porte-vélos à 3 places - Pliable Product Name: Product Code: 59403 Il importe de lire attentivement toutes les instructions avant l’assemblage, l’installation et/ou l’utilisation de ce produit INSTRUCTIONS DE MONTAGE : La barre d’accouplement de votre porte-vélos à 3 places est pré-assemblée en fonction d’un attelage de 2 po.
  • Página 5 Porte-vélos à 3 places - Pliable Product Name: Product Code: 59403 Il importe de lire attentivement toutes les instructions avant l’assemblage, l’installation et/ou l’utilisation de ce produit INSTRUCTIONS DE CHARGEMENT : Placer le récepteur du support à vélos dans le récepteur de l’attelage. Positionner le support aussi près du véhicule que possible.
  • Página 6 Porte-vélos à 3 places - Pliable Product Name: Product Code: 59403 Il importe de lire attentivement toutes les instructions avant l’assemblage, l’installation et/ou l’utilisation de ce produit REMARQUES IMPORTANTES : • Ce support à vélos a été conçu pour transporter trois (3) vélos, en autant que le poids maximum sur le support ne dépasse pas 45 kg (100 lb).
  • Página 7 Cargador para 3 bicicletas - Plegable Product Name: Product Code: 59403 Lea todas las instrucciones atentamente antes de armar, instalar y/o usar este producto. INSTRUCCIONES PARA ARMAR: La espiga para el cargador de 3 bicicletas viene pre-armada para usarse con un enganche de 2”.

  • Página 8: Instrucciones De Carga

    Cargador para 3 bicicletas - Plegable Product Name: Product Code: 59403 Lea todas las instrucciones atentamente antes de armar, instalar y/o usar este producto. INSTRUCCIONES DE CARGA: Coloque el receptor del portabicicletas en el enganche receptor. Ajuste el portabicicletas lo más cercano al vehículo como sea posible.
  • Página 9 (ya sea que colisione o al tratar de evitar las bicicletas y/o la bandeja caídas). • Las bandejas ROLA™ están cubiertas con polvo para evitar la oxidación. Al igual que con cualquier equipo de metal, se recomienda que conserve la bandeja limpia y retire las sales y suciedades recogidas en la carretera.