General Information; Unpacking; Accessory Box; Assembly - Centurion 006104-1 El Manual Del Propietario

General Information

1.1 UNPACKING

• Remove all packaging material.
• Remove separate accessory box.
• Remove the generator from carton.

1.1.1 ACCESSORY BOX

Check all contents. If any parts are missing or damaged, locate an
authorized dealer at 1-888-436-3722.
• 1 - Owner's manual
• 1 - Bottle of Oil SAE 30 with funnel
• 3 - Product Registration Cards (English, Spanish, French)
• 2 - 8" WHEELS
• 1 - Axle
• 1 - Frame Foot
• 1 - Handle with grip
• 1 - Hardware Bag
– 1 - Plastic Spacer
– 1 - Handle Bracket
– 2 - Rubber Bumpers
– 2 - Cotter Pins
– 2 - M8-1.25 Hex Flange Nuts

1.2 ASSEMBLY

The generator requires some assembly prior to using it. If
problems arise when assembling the generator, please call the
Generator Helpline at 1-888-436-3722.
The following tools are required to properly assemble the
generator:
• Needle-nose pliers
• Ratchet and 12mm (1/2") socket
• 12mm (1/2") box wrench or adjustable wrench

1.2.1 ASSEMBLING THE ACCESSORY KIT

The wheels are designed for the unit to greatly improve the
portability of the generator.
The wheels are not intended for over-the-road-use.
1. Refer to Figure 1 to install the wheels as shown.
– Slide the axle through the frame brackets.
– Slide on the wheels then install the cotter pins.
2. Refer to Figure 1 to install the wheel bumpers as shown.
– Secure the two rubber bumpers to the frame foot using
two M8-1.25 Hex Flange Nuts (if not already assembled).
– Place the frame foot under the frame and secure with two
M8-1.25 x 16 bolts.
3. Refer to Figure 2 to install the handle assembly as shown.
– Install the handle bracket to the frame using two M8-1.25
x 40 bolts (if not already assembled).
– Slide the plastic spacer onto the handle assembly then
align with the holes in the handle bracket (if not already
assembled).
4
– 2 - M8-1.25 x 40 Bolts
– 1 - M6-1.0 x 40 Bolt
– 2 - M8-1.25 x 16 Bolts
– 1 - M6-1.0 Hex Flange Nut
NOTICE:
– Secure the handle assembly to the handle bracket using
the M6-1.0 x 40 bolt and one M6-1.0 hex flange nut.
Figure 1 – Wheel Assembly
Figure 2 – Handle Kit
1x HANDLE BRACKET
1x M6-1.0X40 BOLT
1x PLASTIC SPACER
1x HANDLE W/GRIP

1.3 EMISSION INFORMATION

The Environmental Protection Agency requires that this generator
comply with exhaust emission standards. The generator is
certified to meet the applicable EPA emission levels. It is important
that you follow the maintenance specifications provided in this
manual to ensure that your engine complies with the applicable
emission standards for the duration of the engine's life. This engine
is certified to operate on gasoline. The emission control system on
your generator consists of the following:
• Fuel Metering System
– Carburetor
– Fuel Lines
• Air Induction System
– Intake Pipe/Manifold
– Air Cleaner
The Emissions Compliance Period referred to on the Emissions
Compliance label indicates the number of operating hours for
which the engine has been shown to meet Federal Emissions
requirements.
M8-1.25 x 40
BOLTS
1 X M6-10 HEX FLANGE NUT
• Ignition System
Spark Plug
–
Ignition Coil
–