Publicidad
Idiomas disponibles
Idiomas disponibles
Assembly of 010 balustrade
32. Screw part 033063 onto stay 046036 with screw 011038 (Fig. 1).
33. Position components 033063 on landing, using components 002040 and 001004. Drill landing with a 5 mm
bit, keeping a distance between centres that allows at least four balusters to be fitted.
34. Position balusters 127014, with components 033078 facing outwards, and tighten component 001004 (Fig. 1).
35. Fix straight handrail 140053 using components 002031 (Fig. 1).
36. Depending on position and presence of walls around the stairwell, it may be necessary to position one or two
extra balusters 127014 (Fig. 9).
37. In this case, a space must be considered that is at the same distance from the other balusters or from the
wall. Drill landing with a 4.5 mm bit and assemble with components 033063, 001004 and 002040 (Fig. 1)
(Fig. 9).
38. Assembly of floor-mounted balustrade, if applicable (Fig. 16)
Determine the position of the posts on the floor, on average one every 28 cm and at a distanza of 8 cm from
the edge.
Take care: for circular balustrades, use the circular handrail to determine the distance of the posts from
the edge of the floor aperture – this distance varies according to the radius of the circular handrail supplied.
Drill with a Ø 10 mm bit and insert the 046015 components, fixing them with chemical resin (not supplied).
Assemble components 033063 with components 009002 and 005001. Insert the 127014 balustrade
balusters ( H= 910 mm) into the 033063 components, with the 126034 reinforcing baluster about every
metre, and lock them with components 001004. Fix the balusters to the wall using component 033010 and
items 008004, 011053 and 033056 (drill with an Ø 8 mm bit). Determine the length of the handrails and
cut off the excess quantity. Assemble the 140053 or 140073 handrails to the balusters with the 002031
components using items 031076 and 046011 for straight balustrades and items 031073, 031077 and
002011 for circular balustrades. Assemble any 033103, 033105, 033107 connecting components and the
033103 terminal components.
39. Insert the steel cables into the 034041 parts on the banisters, positioning parts 031098 and 001012 on
each end baluster of the banisters and also on one intermediate baluster positioned between the two ends
of the banister side. Fasten the cables at one of the two ends using parts 031098 and 001012, leaving
about 15mm protruding from parts 034041; cover with parts 034042 and 001011. Tighten the cables by
hand and lock parts 031098 and 001012 respectively working from the lower to the higher end of the steel
cable. Once the final parts 031098 and 001012 have been fastened, cover the ends of the cables with
adhesive tape to prevent them from unravelling whilst being cut. Cut the cables at a distance of 15 mm from
parts 034041. Remove the tape and cover with parts 034042 and 001011 (Fig. 1 - 6 - 7).
Final assembly
40. To further reinforce the staircase at intermediate points, fix components 033010 to wall and join to the
balusters, using components 033056. Drill with an 8 mm bit and use components 008004, 011053,
011057, 005035 (Fig. 12) (Fig. 13).
Assembly of 020 railing
41. Unlock component 005008 and fan out the 103012 - 103013 treads. It's now possible to ascend the
staircase.
42. Fit parts BE9 into holes on treads with edge facing upwards (Fig. 2).
43. Starting from the landing, insert the 127002 connecting balusters between the treads, inserting the BF3
component on each tread, with the hole in the screw facing in the direction of the ascent. If necessary, cut
the 127002 balusters from the lower end to obtain a handrail height of about 100 cm.
44. Position balusters with component 033147 with the part with hole upwards (Fig. 2) (Fig. 9). Tighten the
001013 components of the treads above and below paying attention to the riser (Fig. 2).
45. Carefully check that all balusters positioned are vertical. This is essential for successful final assembly of the
staircase.
46. Definitively tighten component 005008 (Fig. 9).
47. Fix component BF1 to floor in position of first baluster, drilling with an 8 mm bit. Use components 011053,
008004, and 001004 (Fig. 2).
48. Position the first baluster 127002; adjust height according to the balusters fitted earlier (Fig. 2). Insert the
046050 reinforcing component into the 1st baluster.
49. Prepare spiral handrails, components 031073, 002011 and disks 031077; the disks are made in soft
transparent material; take care not to mistake them for parts 031076, made in hard transparent material
and to be used only in the joints of any straight handrails present (Fig. 2).
50. Cut the initial handrail by 5 cm and attach the 031061 component, using components 011069 and 004034,
10 - Genius 010 - 020_2:Easy
Publicidad
