Descargar Imprimir esta página
Eaton LUMARK WP Wall Pack LED Instrucciones De Instalación

Eaton LUMARK WP Wall Pack LED Instrucciones De Instalación

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

IB514036EN
Installation Instructions – WP Wall Pack LED
Instructions d'installation – WP Wall Pack LED
Instrucciones de instalación – WP Wall Pack LED
Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this
product must be performed by a qualified electrician. This product must be installed in accordance
with the applicable installation code by a person familiar with the construction and operation of the
product and hazards involved.
Risk of Fire and Electric Shock- Make certain power is OFF before starting installation or attempting
any maintenance. Disconnect power at fuse or circuit breaker.
Risk of Fire- Refer to product label for specific minimum supply conductor requirements.
Risk of Burn- Disconnect power and allow fixture to cool before handling or servicing.
Risk of Personal Injury- Fixture may become damaged and/or unstable if not installed properly.
Failure to comply with these instructions may result in death, serious bodily injury and property damage.
N
otee:
These instructions do not claim to cover all details or variations in the equipment, procedure, or process
described, nor to provide directions for meeting every possible contingency during installation, operation
or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for
user's purpose, please contact your nearest representative.
N
otee:
Specifications and dimensions subject to change without notice.
DISCLAIMER OF LIABILITYe: Eaton assumes no liability for damages or losses of any kind that may arise from the
improper, careless, or negligent installation, handling or use of this product.
NOTICEe: Green ground wire provided in proper location. Do not relocate.
ATTENTION Receiving Departmente: Note actual fixture description of any shortage or noticeable damage on
delivery receipt. File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be
filed within 15 days of delivery. All damaged material, complete with original packing must be retained.
Safety: This fixture must be wired in accordance with the National Electrical Code and applicable local codes and
ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under
installation section.
APPLICATIONS: This lighting fixture is designed for outdoor lighting services, and should not be used in area
of limited ventilation or inside high ambient temperature enclosures. It must be stored in a dry location prior to
installation. Do not expose lighting fixture to rain, dust or other environmental conditions prior to installation
and insertion of photo control or shorting cap (if so equipped). Best results will be obtained if installed and
maintained according to the following recommendations.
WARNING
Brand Logo
reversed out of
black
Lumark
INS #
INS #

Publicidad

loading

Resumen de contenidos para Eaton LUMARK WP Wall Pack LED

  • Página 1 Specifications and dimensions subject to change without notice. DISCLAIMER OF LIABILITYe: Eaton assumes no liability for damages or losses of any kind that may arise from the improper, careless, or negligent installation, handling or use of this product. NOTICEe: Green ground wire provided in proper location. Do not relocate.
  • Página 2 Figure 2. the fixture housing and the mounting surface. If you remove one of the conduits plugs and use an alternate conduit location, add thread sealing tape to plug to ensure watertight seal. EATON IB514036EN Installation instructions...
  • Página 3 Les caractéristiques techniques et les dimensions sont sujettes à modifications sans préavis. EXONÉRATION DE RESPONSABILITÉ e: Eaton n’assume aucune responsabilité pour les dommages ou pertes de quelque nature que ce soit pouvant découler d’une installation, d’une manipulation ou d’une utilisation inappropriée, imprudente ou négligente de ce produit.
  • Página 4 Si vous retirez l’un des capuchons du conduit et utilisez un autre emplacement alternatif, ajoutez du ruban d’étanchéité pour filets sur le capuchon pour assurer une étanchéité à l’eau. EATON IB514036EN Instructions d’installation...
  • Página 5 Las especificaciones y las dimensiones están sujetas a cambios sin previo aviso. RENUNCIA DE RESPONSABILIDADe: Eaton no asume ninguna responsabilidad por daños o pérdidas de ningún tipo que puedan derivarse de la instalación, manipulación o uso incorrecto, descuidado o negligente de este producto.
  • Página 6: Instalación

    Si retira uno o más tapones de los conductos y usa una ubicación alternativa en el conducto, agregue cinta para el sellado de roscas en el tapón para garantizar un sello impermeable. EATON IB514036EN Instrucciones de instalación...
  • Página 8 Warranties and Limitation of Liability Please refer to www.eaton.com/LightingWarrantyTerms for our terms and conditions. Garanties et limitation de responsabilité Veuillez consulter le site www.eaton.com/LightingWarrantyTerms pour obtenir les conditions générales. Garantías y Limitación de Responsabilidad Visite www.eaton.com/LightingWarrantyTerms para conocer nuestros términos y condiciones.