Configuration And Operation; Cleaning And Maintenance - Sonia Tyl H1103 Manual De Instrucciones

CONFIGURATION AND OPERATION

● Connect the power cable to the mains.
- The water level inside the tank must stand
between the "MIN" and "MAX" levels.
- Press
on the control panel and the power
indicator lights up blue. The unit remains in
standby mode and the control panel shows the
following configuration:
• The timer will show 15 minutes.
• The steam volume indicator shows the
maximum level.
• The ozone function indicator is off.
• The heating
• Press the
standby mode and the heating and steaming
functions.
· If the indicator
function is active. The timer will show 30 min
by default and start counting down.
Once the heating temperature has been
reached, it will be maintained until the timer
reaches 0.
• If the indicator
function is active. The timer will show 15 min by
default and start counting down.
After a few minutes, steam will start to come
out of the arm head nozzle.
• Set the timer using the
establish the operating time of the different
functions.
· The heating function
90-minute range.
· The steaming function
30-minute range.
This function allows defining the operating
time for both functions: heating and
steaming.
• Use the "ENERGY" button to adjust the steam
volume to be produced by the nozzle
· If the indicator
volume is at maximum level.
· If the indicator
volume is at half level.
· If only one line of the indicator
the steam volume is at the minimum level.
• Activate the Ozone function by pressing the
"OZONE" button. The ozone function indicator
will light up green. Press again to deactivate the
function and the indicator will turn off.
Bear in mind:
• The heating function is a heat conservation
function.
• If, before activating the steaming function,
the heating function has been activated, the
steam is produced faster compared to a direct
EN
6
and steam indicators
button to switch between the
lights up red, the heating
lights up green, the steaming
or buttons to
allows a 5 to
allows a 1 to
lights up in full, the steam
lights up in half, the steam
lights up,
steaming function activation.
• The ozone function indicator will only light
up green when the steam function has been
selected.
• If the timer shows "E2" when using the heating
or steaming functions, the "WARNING"
indicator flashes and an acoustic signal sounds,
this indicates that the water level is too high.
The active function will stop immediately.
Any locked functions will be unlocked as the
water level returns between "MAX" and "MIN".
Press
• If the timer shows "E1" when using the heating
or steaming functions, the "WARNING"
are off.
indicator flashes and an acoustic signal sounds,
this indicates that the water level is too low. The
active function will stop immediately.
Fill with distilled water to unlock functions and
resume operation.
• If you need to change the essential oil, remove
the cotton by opening the sliding lid at the top
of the arm head nozzle, use tweezers to remove
the cotton and replace it with a new one. Add
oil as required.
• Adjust the sound volume of the acoustic signals
of the steamer: with the unit turned off, press
and hold the "ENERGY" button until the timer
reads "5". This is the default sound volume,
which you can adjust using
to 9, where 0 is the min. volume and 9 the max.
volume. As you do so, the selected value flashes
and is saved automatically.

CLEANING AND MAINTENANCE

● Before cleaning the device, unplug it from the
mains.
● Clean the device with a soft, dry cloth. Do not use
liquids to clean it.
● Despite recommending the use of distilled water to
prevent calcification of the elements, it is advisable
to regularly clean the heating resistor and the level
sensors in order to guarantee the correct operation
of the steamer and prevent the appearance of
possible error messages.
To do so, fill up the water tank with vinegar and
leave it in place for about 10-15 minutes, making
sure that the resistor and sensors are covered by
the vinegar. Then rinse as many times as necessary
with plenty of water until all the vinegar and its
smell have gone.
● For maintenance or repairs of any part of the
product, please contact your distributor or
specialised technician.
RECYCLING
If you need to dispose of the product or any of its
parts or accessories, please check and respect the
laws and regulations applicable to waste management
and environmental protection.
to resume operation.
or from 0