Publicidad
ENGLISH
Portable, self-contained basin
Ref. 061430
Contents & available spares
- Casing for portable, self-contained basin..
060610 - Detachable transom for attachment to portable basin.
080418 - 1 box dispenser of gloves, tissue or towels.
460236 - Electronic soap dispenser (uses batteries).
461008 - Turning tap 140x200x1/2" (50mm nut).
454260 - Flexible drainage pipe for self-contained basin.
461430 - 10-litre tank for self-contained basin.
461428 - Translucent 10-litre tank for clean water.
454202 - 2 ½" Valve with trough for 500mm sink.
421002 - M4x16-mm metric thread hex head screw.
421050 - Hexagon nut metric thread M4.
421004 - M5x8-mm metric thread hex head screw.
421052 - M5-mm metric thread hex nut.
409822 - Plastic nylon Fisher 6X30mm peg.
421038 - Plate thread bolt 22x4,8mm. DIN 7981 A2.
461432 - "Not drinking water" vinyl adhesive for tank.
Other spares:
460408 - Hydraulic pedal.
485020 - 50x18-mm.ø plastic wheel for self-contained basin.
Read the instructions before connecting the device and store them in a safe place for reference.
DO NOT DRINK WATER FROM THE HAND WASHBASIN. THIS DEVICE
IS NOT DESIGNED FOR DRINKING WATER.
This hand washbasin cannot replace any items that require hot and cold running water at the
facilities in accordance with the applicable laws.
Assembly
Check the contents.
When assembling, it is advisable to use special gloves not to get cuts on hands.
Pull out front door and remove the plastics from doors and washbasin.
Insert the backsplash sliding it along the rails and secure it to the back of the basin
using the nuts and screws.
Remove the front part of the soap dispenser using the key provided.
Attach the soap dispenser to the backsplash using the nuts and screws.
Introduce four AA batteries into the battery compartment
Fill the soap container and replace the front part of the soap dispenser.
Secure the tissue dispenser using nuts and screws.
English
FRICOSMOS
Insert the spout in the upper orifi ce and fi x it with the provided bolts
Assemble the drain valve
Connect to the spout the closest hose.
Insert the tank with the label of non-drinking water under the spout.
Connect the fl exible drain pipe to the valve making a U-bend and attach the other end
to the dirty water tank
Remove the small plug from the clean water tank and insert the remaining hose
through this hole.
Make sure that it runs under the handle
When using it for the fi rst time, step down and release the button all the way repea-
tedly until the water comes out.
Then step down and release repeatedly.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
· Fig. 1
· Fig. 3
· Fig. 4
· Fig. 5
Use
Cleaning and sterilization
Wash both tanks with plenty of drinking water.
Sterilize before the fi rst use of each day, by adding a sterilizing product approved
for drinking water according to the instructions of the manufacturer. Feed all the
circuit with the water and the sterilizing product stepping on the button until the
tank is empty.
Then fi ll the tank with drinking water. It is now ready for use.
Perform this procedure before the start of each day.
Safety
Empty the tank of used water at least once an hour or when is full.
Empty the tank of drinking water at least once every 6 hours.
When the device is not being used for a long period of time, empty the tanks, wash
them and store them completely dry.
Store the containers clean and dry in a dark, dry and healthy area.
Replace the tanks every six months.
In order to avoid cross-contamination, do not use the bin.
Maintenance of stainless steel
Use only water and neutral soap when cleaning.
Wipe with a soft cloth.
Rinse with plenty of water.
Dry with a soft cloth.
Do not use acids or strong detergents and do not rub with a scourer or spatula.
All sizes are described in mms. This device has two years of warranty. An improper use void the warranty of
the unit.
· Fig. 2
English
FRICOSMOS
Publicidad
