Cequent Towing Products 36426 Instrucciones De Instalación

Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 36426F
Wrenches: 9/16, 3/4, 10mm
Drill Bits: ½"
Carriage bolt can be accessed
behind vehicle end panel to assist
in positioning.
1 1 1 1 Qty. (2) Carriage Bolt 3/8" x 1-1/2"
2 2 2 2
Qty. (2) Reinforcing Plate 3/8"
3 3 3 3 Qty. (2) Spacer (round hole) ¼" x 1" x 2"
4 4 4 4 Qty. (2) Hex Nut 3/8"
5 5 5 5
Qty. (2) Conical toothed washer 3/8"
1. Tape spacers (3) into position. Feed fishwires through spacers (3) and out the end of the steel bumper. Slide reinforcement plate
(2) onto fishwires then thread carriage bolts (1) onto fishwire. Gently pull reinforcement plate and carriage bolt into position.
Leave the bolt leaders attached or tape carriage bolts into position.
2. Raise hitch into position and install conical toothed washer (5) and nut (4).
3. Using the hitch as a template, drill four 1/2" holes through frame rail.
4. Remove fuel line support bracket bolt, using a 10mm socket on passenger side.
5. Start with most rearward hole feed fishwire through hole in frame bracket, 1/2" hole in frame rail and access slot in frame rail as
shown.
6. Feed fishwire through spacer (7), attach to carriage bolt (6), and pull fasteners through slot and into position as shown.
7. Loosely install lock washers (8) and nuts (9) onto carriage bolts.
8. Reinstall bolt for attaching the fuel line support bracket that was removed in step 4.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z 2006, 2015 Cequent Towing Products – Printed in Mexico
Installation Instructions
Pontiac G6
Pontiac G6 GT & GTP
Fascia
(Sold separately)
Drawbar Kit:
36065
Drawbar must be used in the
Rise position only.
6 6 6 6
7 7 7 7
8 8 8 8
9 9 9 9
Tighten all 3/8-16 GR5 fasteners to 31 lb.-ft. (41 N*M)
Tighten all ½-13 GR5 fasteners0 to 75 lb.-ft. (75 N*M)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
3500 LB, (1589 Kg) Max Gross Trailer Weight
300 LB, (136 Kg) Max Tongue Weight
Wiring Access Location: PC3. PC4
Frame Rail
Drilled Holes
Both Sides
Qty. (4) Carriage Bolt ½" x 1-3/4"
Qty. (4) Reinforcing Plate ½"
Qty. (4) Lock washer ½'
Qty. (4) Hex Nut ½"
36426N
Part Numbers:
36426
06463
90159
10-13-15 Rev. D
Form: F205 Rev A 5-6-05