Cequent Towing Products 36479 Instrucciones De Instalación

Frame rail Fascia
Cut outs for clarity Bulk head
Hitch Shown In Proper Position
Equipment Required: Pull wires (Provided)
Fastener Kit: 36479F
Wrenches: 11/16, 3/4
Drill Bits: 1/2", 3/8"
Note: Bumper material is very
tough and difficult to drill. Use
Rotabroach hole cutting tool –
Towing Products part number"
40109 - 3/8" or carbide drill.
(sold separately)
Lowering exhaust on vehicle
that require drilling in end
panel for ease of installation.
Fasteners same both sides
1 1 1 1
Qty. (2) Carriage Bolt 3/8-16 x 1.50 GR5
2 2 2 2 Qty. (2) Spacer 1/4 X 1 X 2 Sq Hole
3 3 3 3 Qty. (2) Spacer 1/4 X 1 X 2
4 4 4 4 Qty. (2) Conical Washer 3/8"
5 5 5 5 Qty. (2) Nut 3/8-16
Instructions for vehicle without hole in end panel.
1. Raise hitch into position. Position the hitch against the end panel centering the over the bumper attachment bolt (A). Make sure the bracket
is flat against the frame rail. Check alignment.
2. Using the hitch as a template mark and center punch hole locations. Drill two 3/8 hole through end panel. Remove burrs.
Continue with remaining instructions.
Instructions for vehicle with hole in end panel.
1. Tape spacers (Item 3) into position. Feed pull wire through spacers (Item 3) behind end panel. Slide spacer
(Item 2) onto pull wires then thread carriage bolts (Item 1) onto pull wire. Gently pull reinforcement plate
and carriage bolt into position. Leave the bolt leaders attached or tape carriage bolts into position.
2. Raise hitch into position and install conical washer (Item 4) and nut (Item 5).
3. Using the hitch as a template, drill two 1/2" holes through frame rail.
4. Feed pull wire through hole in frame bracket, 1/2" hole in frame rail and access slot in frame rail as shown.
5. Feed pull wire through spacer (Item 7), attach to carriage bolt (Item 6), and pull fasteners through slot
and into position as shown.
6. Loosely install lock washers (Item 8) and nuts (Item 9) onto carriage bolts.
7. Torque all fasteners to specifications.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z 2008, 2015 Cequent Towing Products – Printed in Mexico
Installation Instructions
End
Chevrolet Malibu
panel
(Sold separately)
Drawbar Kit:
Drawbar must be used in the
RISE position only.
Frame rail
1/2" Pull wire
4
5
View of vehicle
8
with existing hole
9
Access hole
Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 Lb.-Ft. (47 N*M)
Tighten all 1/2-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Saturn Aura
36065
3500 LB (1589 Kg) Max Gross Trailer Weight
300 LB (136 Kg) Max Tongue Weight
Existing hole in some
vehicles
3/8 " Pull wire
A
3
2
1
6
7
6 6 6 6
Qty. (2) Carriage Bolt 1/2-13 X 1.75 GR5
7 7 7 7 Qty. (2) Spacer 1/4 X 1 X 3 Sq Hole
8 8 8 8 Qty. (2) Lock Washer 1/:"
9 9 9 9 Qty. (2) Nut 1/2-13
Sheet 1 of 3
Part Numbers:
36479, 90194
06658, 36327
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Wiring Access Location: PC1, PC2
Lower exhaust on dual exhaust
system for ease of installation.
Vehicle needs to be jacked up if
installation is from ground level.
End
panel
3/8 " Hole to be drilled hole on
vehicle without existing hole
1/2" Hole to drilled on all vehicles
View of vehicle without
existing hole
36479N 10-13-15
Form F206 Rev A 5605
U-Haul
Rev. C