Imperia PrestoCheese Manual De Instrucciones página 6

Before operating the machine, check that the mains voltage of your home corresponds with the one given
in the technical sheet of this manual and on the machine data plate. Do not use any other type of supply.
The manufacturer disclaims any liability for damage to persons or property deriving from the failure to adhere to
this rule. Where necessary fit an adapter for the plug, making sure that it is suitable for the power lead.
CAUTIONS.
This device is not intended for use by persons (including children) with impaired physical, sen-
sorial or mental ability, or without experience and knowledge, unless they have received instructions about
the use of the device and are controlled by a person responsible for their safety.
Children should be controlled to make sure they do not play with the device.
Do not insert foreign substances in the cheese hopper compartment. For reasons of hygiene you are advised
to gather your hair in a protective cap. Place the machine on a firm surface, able to bear its weight.
Before using the machine make sure you know how to stop it quickly in an emergency.
Do not use the machine if:
- it is not working properly;
- it has been damaged or dropped;
- if the power lead or plug are damaged.
Never put the machine and/or its parts in water. Keep them away from hot surfaces.
Do not allow the power lead to hang from tables or furniture. Do not use this machine near sinks or on wet surfaces.
DESCRIPTION OF THE MACHINE
The machine components are:
A – MOTOR BODY
B – PUSHBUTTON
C – PESTLE
D – GRATER ROLLERS
Before each time of use: Follow the instructions given in the "Cleaning and maintenance" paragraph.
CAUTION.
All assembly operations should always be carried out with the machine stopped and the plug disconnected.
1. Insert one of the grater rollers (D) in the roller housing (L) of the motor body (A) with the pin (milled end) for
coupling to the motor shaft as shown in Fig. 2 (step 1).
2. Insert the front knob (E) on the cylindrical end of the grater roller (D) and at the same time in the knob housing
of the motor body (A) Fig. 2 (step 2).
3. Turn the front knob (E) clockwise until obtaining firm coupling with the motor body (A) as in Fig. 2 (step 3).
4. Under the tray (F) insert the cover (G) Fig. 2 (step 4).
5. Insert the tray (F) complete with cover (G) in the housing of the motor body (A) push it as far as it will go, making
sure that the two catches (M) at the sides of the tray are correctly in place in relation to the sides of the machine
body. Fig. 2 (step 5).
6. Slightly slope the machine, release the power lead retainer lid and take the lead out. Fig. 2 (step 6).
At the end of every time of use: follow the instructions given in the "Cleaning and maintenance" paragraph.
CAUTION. All disassembly operations should always be carried out with the machine stopped and the plug
disconnected. For disassembly operations, reverse the sequence followed for assembly, i.e. starting from
point 6 up to point 1.
Set the machine on a suitable surface able to support its weight, put the plug in the power socket. Put the cheese
to be grated (prepared previously cut into pieces of the right size) in the hopper compartment (H) shown in Fig. 3.
Exert a light pressure on the cheese with the pestle (C). Press the pushbutton (B) to operate the machine.
CAUTIONS.
NEVER USE YOUR FINGERS TO PRESS THE PIECES PUT IN THE MACHINE OR USING ANY
OTHER OBJECT, ALWAYS USE THE PESTLE PROVIDED (C).
When the plug is put in the socket the warning light under the button (B) lights up.
The machine starts working only with the tray (F) completely inserted, the pestle (C) down, and the pushbutton (B)
Pressed. If even only one of these conditions fails to be met the machine will either not start or it will stop.
ELECTRICAL CONNECTION
E – FRONT KNOB
F – TRAY
G – TRAY COVER
H – HOPPER
MACHINE ASSEMBLY
MACHINE DISASSEMBLY
USE OF THE MACHINE
I – POWER LEAD
L -
M – CATCHES
(fig.2)
(fig.3)
6
(fig.1)
KNOB HOUSING