WOOD'S AC Palermo 18K Manual De Instrucciones página 16

Operating Instructions
GB
FUNCTION OF THE OPERATION MODES AND INSTALLATION DESCRIPTIONS
A. Accessories
After unpacking, please check whether
the above-mentioned accessories are
included, and check their purposes in
the installation introduction in this
manual.
B. Mobile air conditioner
J. Appearance and Function of Remote
Control.
Notes:- Do not drop the remote control.-
Do not place the remote control in a
location exposed to direct sunlight.
M. Operation Introduction
Before starting operations in this section:
1) Find a place where there is power
supply nearby.
2) Install the exhaust hose, and adjust
the window position well.
3) Connect drain hose well (only for using
heating model);
4) Insert the power cord into an grounded
AC220~240V/50Hz socket;
5) Press the POWER button to turn on
the air-conditioner.
K&L. Introduction to Exhaust Hose
Installation
A) Temporary installation
1.Twist the exhaust hose into the Hose
Connector. and the outlet at back of the air
conditioner
2.Put the other end of the exhaust hose
to the near windowsill.
N. Window Slider Kit Installation
The installation manner of window slider
kit is mostly in "horizontal" and
"vertical". As shown Fig.5 and Fig.5a,
check the min. and max. size of the
window before the installation.
1. Install the window kit on the window ;
2. Adjust the length of the window slider
kit according to the window width or
height, and fix it with the dowel;
3. Insert the Window Connector hose to
the hole of the Window Kit.
O. Internal Tank Water Full Alarm
16
Function
The inner water tank in the airconditioner
has one water level safety
switches, it controls water level. When
water level reaches an anticipated
height, the water full indicator lamp
lights up. (when the water is full, please
remove the rubber blockage at the bottom
of unit, and all water will be drained
outside.)
H. Maintenance Explanations
Declaration:
It is very important that the filter
is cleaned regularly; otherwise
the air conditioner might lose
capacity and even be seriously
damaged.
1) Before cleaning, be sure to
disconnect the unit from any electric
supply outlet;
2) Do not use gasoline or other
chemicals to clean the unit;
3) Do not wash the unit directly;
4) If the conditioner is damaged,
please contact the dealer or repair
shop.
1. Air Filter
-If the air filter becomes clogged with
dust/dirt, the air filter should be
cleaned once every two weeks.
-Dismounting
Open the air inlet grille and take off air
filter.
-Cleaning
Clean the air filter with neural
detergent in lukewarm ( 40°C ) and
dry it up in the shade.
-Mounting
Putting the air filter into the inlet grille,
replace the components as they were.
2. Clean the Air-conditioner Surface
First clean the surface with a neutral
detergent and wet cloth, and then
wipe it with a dry cloth.
E. Before using
Check up whether the exhaust hose
has been mounted properly.
Cautions for cooling and
dehumidifying operations:
-When using functions on cooling and
dehumidifying, keep an interval of at
least 3 minutes between each
POWER.
-Power supply meets the
requirements.
-The socket is for AC use.
-Do not share one socket with other
appliances.
-Power supply is
AC220-240V, 50Hz
When unplugged: All keys and indicator
lights are not visible.
When plugged in: The indicator light of
power key and timing key is half on for
operation.
1. POWER KEY
Press to turn unit "ON" or "OFF"
2. FUNCTION
Press this key to select cooling,
dehumidifying or fan.
3. TEMPERATURE REGULATION KEY (UP)
During cooling function: This key raises the
preset temperature by 1℃ each time it is
pressed and the maximum limit is 30℃ .
During timing function: Increasing timing
time,This key raises the time by 1 hour
each time it is pressed and increasing
cycle.
4. TEMPERATURE REGULATION KEY
(DOWN)
During cooling function: This key lowers
the preset temperature by 1℃ each time it
is pressed and the minimum limit is 17℃.
During timing function: Decreasing timing
time,This key lowers the time by 1 hour
each time it is pressed and decreasing
cycle.
5. L.E.D. DISPLAY
The display indicates the current setting