Vimar ELVOX 6621 Instrucciones Instalador página 9

6600
Programming the push-buttons
The video-interphone is supplied with 3 push-buttons for the following
functions: lock release, self-start and "stair light" auxiliary service, which
activates the 1st relay of the 1st actuator (type 69HR), if connected to the
installation and with other 6 push-buttons for intercommunicating calls or
auxiliary services.
To change the operation type of push-buttons it is necessary to use pro-
grammer type 950C or SaveProg, with the exception of the assignation of
the functions for the intercommunicating calls and self-start to a specific
entrance panel.
Programming the push-buttons for the intercommunicating calls
(With series 8870, Giotto, Petrarca raise the handset of the interphone
/ video-interphone to call. On the 6600 series keep pressed the talk /
listen push-button "I").
Programming phase:
1) Press and hold down "I".
2) Press and hold down also "H" together with "I".
3) Wait for nearly 3 seconds until the red led "M" flashes.
4) Now the microprocessor is physically reset.
5) Release both push-buttons "I" and "H"
6) Press and hold down the "F" push-button to be programmed.
7) After 2 seconds the video-interphone emits a high-pitched tone, while
the other interphone / video-interphone emits a three-tone ascending
scale.
8) Release the "F" push-button related to the intercommunicating call.
9) On the called interphone / video-interphone (the one with the three-
tone scale) press one of the push-buttons programmed as door lock or
F1 or F2 or the auxiliary one.
10) A high-pitched tone confirms the end of the procedure.
Repeat the procedure also for the other interphones / video-interpho-
nes ad possible intercommunicating call push-buttons.
Programming the self-start push-button to a specific entrance panel.
Programming phase:
1) Press and hold down "I".
2) Press and hold down also "H" together with "I".
3) Wait for nearly 3 seconds until the red led "M" flashes.
4) Now the microprocessor is physically reset.
5) Release both push-buttons "I" and "H"
6) Press and hold down the "F" push-button to be programmed.
7) After nearly 2 seconds the video-interphone emits a high-pitched tone.
8) Release the push-button "F" related to the self-start.
9) On the entrance panels with push-buttons press the call push-button
corresponding to the video -interphone; on the alphanumeric entrance
panel, on the contrary, enter the call code and press "
10) A high-pitched tone will confirm the end of the procedure.
Restoring the default values of push-buttons
Programming phase:
1) Press and hold down "I".
2) Press and hold down also "H" together with "I".
3) Wait for nearly 3 seconds until the red led "M" flashes.
4) Now the microprocessor is physically reset.
5) Release both push-buttons "I" and "H"
6) Press and hold down the push-button to be restored to its default set-
ting.
7) After 2 seconds the video-interphone emits a high-pitched tone.
8) Release the push-buttons and press again the push-button to restore
to its default setting.
Deleting all settings
This procedure is recommended when you want to change the ID of
a previously programmed video-interphone without retaining its pro-
gramming parameters.
Programming phase:
1) Press and hold down "I".
2) Then press and hold down also "H" together with "I".
3) Wait for nearly 3 seconds until the red led "M" flashes.
4) Now the microprocessor is physically reset.
5) Release both push-buttons "H" and "I"
6) Press and hold down the self-start push-button "H".
7) After 2 seconds the video-interphone emits a continuous tone for two
seconds.
8) Release the self-start push-button "H".
9) During the long tone press the lock push-button "G".
If the deletion procedure was successful, press the lock push-button
"G" and the video-interphone will emit a triple "BEEP".
EN
OPERATION
Calls from an entrance panel, intercommunicating calls and landing calls
are differentiated by means of different tones.
Landing calls
Calls from entrance panels do not follow the pressing of the call push-but-
ton but are generated internally by the video interphone. The call time dwell
or cycle consists of a ringtone of 1 second and a pause of 2 seconds,
repeated twice (default setting of entrance panel). The duration of "Ding-
Dong" and "Ding-Dong-Dang" ringtones does not correspond to the time
dictated by the call cycle but to the natural duration of the ringtone. To
answer, press and release push-button "I". If push-button "I" has already
been pressed during the call, release it and press it again The call answer
time (30 s) and the conversation time (2 minutes by default) are set in
the entrance panel parameters. Once the conversation time has elapsed,
conversation can be continued if the call is made again within 10 s, from
the same entrance panel.
During conversation, the audio can be interrupted momentarily (maximum
5 s) by pressing the "I" push-button.To resume conversation, press the
conversation push-button again within 5 s, otherwise communication is
lost. Press push-button "I" to terminate the conversation. The red LED "M"
remains lit while the audio is active.
Intercommunicating call.
Press the intercommunicating push-button, if programmed, for the inter-
phone/video interphone to be called. The loudspeaker of the calling video
interphone will emit a ringing tone (if the call is possible) or an engaged
tone (if the call is not possible). On the called interphone/video interphone
the ringtone starts sequentially at intervals of 1 s ringing and 4 s pause.
The maximum duration of the call is 30 s (6 cycles). If you wish to inter-
rupt the call, press the conversation push-button "I" before an answer is
received from the called device. To answer a call, lift the handset on the
called interphone/video interphone, or press the conversation push-button.
When answered, the video interphone enters direct communication with
the called device. Maximum duration of conversation is 5 minutes. When
the conversation time has elapsed, the user can continue without replacing
the handset if a new call is made within 10 s. Calls from the entrance panel
have priority over intercommunicating calls.
Denied calls.
The chime exclusion is indicated by the permanent lighting of the red LED
"M". If calls are made from the entrance panel to the video interphone when
the call mute is enabled, they are denied. A denied call causes the red LED
"M" to briefly switch off according to the number of times calls are denied
(maximum 4 denied calls). The signal is repeated every 10 s (approx.).
Deletion of denied calls is by re-enabling the ringtone, resetting the video
".
interphone or a system power failure. On the entrance panel, a denied call
is indicated by means of a dissuasion tone (a series of "Beeps" at 100ms
intervals with a pause of 100ms for a total of 5 s). The message "Do not
disturb" also appears on entrance panels with display. The programming
of push-buttons "G" and "I" can be changed through two different configu-
rations ("HANDS FREE" or with the speak/listen push-button PRESSED),
using the programmer type 950C connected to a push-button entrance
panel and/or an alphanumeric entrance panel with software version V4 or
bigger. See instructions for programmer type 950C and entrance panels
or electronic units.
Lock Button
The lock button of each device works in the following manner.
- Device with handset at rest
which it has spoken or from which it has been called.
- Device with handset raised but not engaged in a conversation
to switchboard if the Switchboard flag is YES. Otherwise it goes back
to the first case.
- Device with handset raised and engaged in an internal conversation
as in the first case.
- Device with handset raised and engaged in an external conversation or
called from entrance panel lock
spoken with or from which it has been called.
In practice a lock is always activated except when the handset is raised
and you immediately press the lock button. This can also be taken to the
standard case if the system has no porter switchboard and the Switchboard
flag is set on NO.
NOTE: In series 6600 the equivalent operation is to press for an instant the
"open voice" push-button and then the lock release. Also in this case the
switchboard is called.
lock to the last entrance panel with
to the entrance panel being
call
9