Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
READ ALL INSTRUCTIONS/LISEZ TOUTES LES INSTRUCTIONS/
LEA TODAS LAS INSTRUCCIONES
WARNING: Read all instructions before using the work light. Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
AVERTISSEMENT: Veuillez lire toutes les instructions avant d'utiliser la lampe de travail. Ne pas respecter toutes les instructions
listées
ci-dessous peut entraîner un électrochoc, un incendie et/ou de graves blessures.
ADVERTENCIA: Lea todas las instrucciones antes de usar la luz de trabajo. El incumplimiento de todas las instrucciones
enumeradas,
puede provocar descargas eléctricas, incendios y / o lesiones graves.
INSTALLATION/INSTALLATION/INSTALACIÓN
1
3
1. Extend the "kick stand" to adjust the work light to a suitable angle./Étendre le «pied de support» pour régler la lampe de travail
à un angle approprié./Extienda el "soporte de pie" para ajustar la luz de trabajo al ángulo requerido.
2. Insert the plug to the socket./Fixer la fiche dans la prise./Inserte el enchufe al tomacorrientes.
3. Turn on/off the power./Bancher / débrancher le courant./Encienda o apague el suministro de energía.
2
2
SAFETY GUIDELINES / DEFINITIONS
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property
damage.
RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety precautions should always be followed to reduce the risk
of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property
damage. There are certain applications for which tools and equipment are designed. Manufacturer strongly recommends that this product
NOT be modified and/or used for any application other than for which it was designed. Read and understand all warnings and operating
instructions before using any tool or equipment.
IMPORTANT SAFETY INSTRUCTIONS
WARNING!
When using the worklight, basic precautions should always be followed, including the following:
• Read all the instructions before using the worklight.
To reduce the risk of injury, close supervision is necessary when a worklight is used near children.
•
•
Do not use outdoors.
•
To disconnect, turn all controls to the OFF positon, then remove plug from outlet.
•
Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
•
Unplug from outlet when not in use and before servicing or cleaning.
•
Do not operate any worklight with a damaged cord or plug, or after the worklight has received a sharp blow, malfunctions or
is dropped or damaged in any manner. Return worklight to the nearest authorized service facility for examination, repair, or
electrical or mechanical adjustment.
• To reduce the risk of electrical shock, do not put worklight in water or other liquid. Do not place or store worklight where it
can fall or be pulled into a tub or sink.
• Connect to a properly grounded outlet. Refer to Grounding Instructions.
WARNING:
Do not place the worklight in a positon which may cause anyone to intentionally or unintentionally stare into the light.
Serious eye injury could result.
WARNING: Fire hazard. Do not operate worklight near flammable liquids or in gaseous or explosive atmospheres. Internal
sparks may ignite fumes causing personal injury.
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
TROUBLE SHOOTING
• The work light doesn't work - Check if the power cord is plugged in or the switch is turned on.
• The work light is hard to rotate - Check if the screws are over-tightened.
Grounding Instructions
In the event of malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of
electric shock. The worklight must be connected to a cord having an equipment-grounding conductor and a grounding plug. The
plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and
ordinances.
3
Publicidad
Tabla de contenido
