Charging Procedure; Important Charging Notes - BLACK&DECKER NHT2218 Manual De Instrucciones

Department of Transportation Hazardous Material Regulations (HMR)
actually prohibit transporting batteries in commerce or on airplanes
(i.e., packed in suitcases and carry-on luggage) UNLESS they are
properly protected from short circuits. So when transporting individual
batteries, make sure that the battery terminals are protected and well
insulated from materials that could contact them and cause a short
circuit. NOTE: Batteries should not be put in checked baggage.

ChArgiNg PrOCedUre

the BAttery PACk iS NOt fULLy ChArged At the
fACtOry. ChArge BAttery PACk fOr At LeASt 9 hOUrS
BefOre USe.
The charger is designed to use standard household 120 volt 60 Hz
power.
1. Plug the charger (A) into any standard 120
Volt 60 Hz electrical outlet (figure 1).
2. Slide the charger onto the battery pack (B)
as shown in figure 1 and let the battery pack
charge initially for 9 hours. After the initial
charge, under normal usage, your battery pack
should be fully charged in 6 to 9 hours.
2a) During charging the green LED will appear.
2b) When charging is complete the green LED will
go off.
3. Unplug charger, and remove the battery pack.

imPOrtANt ChArgiNg NOteS

1. After normal usage, your battery pack should be fully charged in
6 to 9 hours. If the battery pack is run-down completely, it may
take up to 9 hours to become fully charged. Your battery pack
was sent from the factory in an uncharged condition. Before
attempting to use it, it must be charged for at least 9 hours.
2. DO NOT charge the battery pack in an air temperature below
+40°F(+4.5°C), or above +105°F (+40.5°C). This is important
and will prevent serious damage to the battery pack. Longest life
and best performance can be obtained if battery pack is charged
when air temperature is about 75°F (24°C).
3. While charging, the charger may hum and become warm
to touch. This is a normal condition and does not indicate a
problem.
4. If the battery pack does not charge properly—(1) Check
current at receptacle by plugging in a lamp or other appliance.
(2) Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights. (3) Move
charger and battery pack to a surrounding air temperature of
40°F (+4.5°C) to 105°F (+40.5°C). (4) If the receptacle and
temperature are Ok, and you do not get proper charging, take or
send the battery pack and charger to your local Black & Decker
service center. See Tools Electric in yellow pages.
5. The battery pack should be recharged when it fails to produce
sufficient power on jobs which were easily done previously. DO
1
NOT CONTINUE using unit with its battery pack in a depleted
condition.
6. The battery pack will reach optimum performance after being
A
cycled 5 times during normal usage. There is no need to run the
battery pack down completely before recharging. Normal usage
is the best method of discharging and recharging the battery
pack.
B
StOrAge reCOmmeNdAtiON
1. Store tool:
excess
2. For prolonged storage such as over the winter, the battery pack
should be fully charged and then removed from the charger. It
should be charged again just prior to use.
LeAviNg the BAttery PACk iN the ChArger
It is Ok to leave battery packs on charge for long periods of time.
The charger has a maintenance mode which gives the battery
7
a.) with the battery pack removed and on the charger.
b.) in a place that is cool and dry away from direct sunlight and
heat or cold.
c.) out of the reach of children.