Memory Reset - Oxygen HYDRA 230V Manual Tecnico

Oxygen Automation strongly suggest to install physical stops, both in opening and in closing, for an accurate installation and preservation of the gate over time.
Hydra Control Board works with times and automatically add some seconds in order to guarantee the total opening and closing in any condition (bad weather,
strong wind, snow and rust). If you don't have physical stops, slowdown speed option is needed (DIP6 = ON)
1) Create two wire links between 11 - 17 and 11- 18 and set DIPs n. 4, 9, 10, 11, 12 to ON. Now you have excluded all the safety inputs(default). 7 Red Lights = ON
2) Please check you have connected the capacitors between black and brown cables of each motor (in parallel connection)
Cables colors are: Grey=common, Brown and Black = opening and closing
3) To save remote controls:
- You can save remote controls only if the gate is closed.
- Set DIP2=OFF (default)
- Switch on power supply and wait for that gate closing automatically (if it opens please reverse brown and black) if the gate stays still it's already closed so it's ok
- when the gate is still in closing position, push and release P1 button, Main Light (Prog.LED) go ON
- Push a Remote Control button, Main Light make one blink
- Wait 10 seconds until Main Light switch off = Remote programmed
If this procedure doesn't work please do the memory RESET procedure and do it again.
4) Please follow the procedure "gate time setting" described in manual (one or two motors depending on your kit, Don't push P1 button if you have two motors)
5) Connect external photocells as per picture 2 (If you have two pairs of photocells, connect the two photocells Receiver contacts in series)
Remove wire link 11 - 18. Do NOT remove wire link 11 – 17
6) Optional: Connect the External Lamp as per picture 1 (flashing)
7) Adjust the Force, as per Force Adjustment chapter. A good setting for electro-mechanical motors is between 3 and 5 flashings
8) Oxygen Automation Service Dept. is at your disposal for any eventuality: service@oxygenautomation.com
CONNECTIONS
N. CLAMPS
1 - 2 230V LIVE AND NEUTRAL
3 MOTOR 1 OPENING
4 MOTOR 1 COMMON
5 MOTOR 1 CLOSING
6 MOTOR 2 OPENING
7 MOTOR 2 COMMON
8 MOTOR 2 CLOSING
9 – 10 FIXED LAMP
11 ACCESSORIES COMMON
12 NC OPEN LIMIT SWITCH M1
13 NC CLOSE LIMIT SWITCH M1
14 NC OPEN LIMIT SWITCH M2
15 NC CLOSE LIMIT SWITCH M2
16 NO START
17 NC STOP
18 NC CLOSING PHOTOCELLS
19 NO PEDESTRIAN START
20 NC OPENING PHOTOCELLS
21 24VAC ACCESSORIES
22 0 VAC ACCESSORIES + LOCK
23 12 VAC ELECTRIC LOCK
24 ANTENNA COMMON
25 ANTENNA INPUT
26 - 27 FLASHING LAMP CONTACT
TWO WINGS GATE SETTING (TWO MOTORS)
- Gate Closed
- Set Dip Switch N.1 = On
- Press Remote Control Button - First Wing Opens
- Wait For Wing Displacement (We Suggest 2 Or 3 Seconds)
- Press Remote Control Button - Second Wing Opens
- First Wing Is Opened - Wait For 1 Or 2 Seconds - Press Remote Control Button To Stop
It
- Second Wing Is Opened – Wait For 1 Or 2 Seconds - Press Remote Control Button To
Stop It
- Wait For Desidered Pause Time In Opening (Normally Between 10 And 30 Secs.)
- Press Remote Control Button - Second Wing Closes
- Wait For Wing Displacement (We Suggest 2 Or 3 Seconds)
- Press Remote Control Button - First Wing Closes
- Second Wing Is Closed - Wait For 1 Or 2 Seconds - Press Remote Control Button To
Stop It
- First Wing Is Closed - Wait For 1 Or 2 Seconds - Press Remote Control Button To Stop
It
- Set Dip Switch N.1 = Off
PEDESTRIAN GATE SETTING
- Gate Closed
- Set Dip Switch N.1 = On
- Press Pedestrian Remote Control Button – First Wing Opens
- Wait For Desidered Opening Angle - Press Pedestrian Remote Control Button To Stop
It
- Wait For Desidered Pause Time In Opening (Normally Between 5 And 10 Secs.)
- Press Pedestrian Remote Control Button - Wing Closes
- Wing Is Closed - Wait For 1 Or 2 Seconds - Press Remote Control Button To Stop It
- Set Dip Switch N.1 = Off
FAST SETTING
DIP SWITCH SETTING
DIP ON
1 TIME SETTING MODE STANDARD MODE
2 STEP BY STEP MODE RESIDENTIAL MODE
3 CONDOMINIUM ON CONDOMINIUM OFF
4 DISABLE INPUT 20 ENABLE INPUT 20
5 ELECTRIC LOCK ON ELECTRIC LOCK OFF
6 SLOWDOWN ON SLOWDOWN OFF
7 +3 MIN. LAMP OFF +3 MIN. LAMP ON
8 HYDRAULIC MOTORS MECHANIC MOTORS
9 DISABLE INPUT 12 ENABLE INPUT 12
10 DISABLE INPUT 13 ENABLE INPUT 13
11 DISABLE INPUT 14 ENABLE INPUT 14
12 DISABLE INPUT 15 ENABLE INPUT 15
- Step by step mode = automatic closing disabled
- Residential mode = step by step and automatic
closing
- Condominium mode = do not accept other START
during the opening
* Hydraulic motors settings: DIP 8 = ON and DIP 6 =
OFF
GATE TIME SETTINGS
FURTHER SETTINGS
ENGLISH
OFF REMOTE CONTROLS STORE
- Push and release P1 button, Led automatically switches ON
- Push a Remote Control button, LED makes one blink, Remote is stored,
Until LED is "ON" it's possible to add more remote controls
- Wait for 10 seconds until LED switch OFF automatically
*You can save remote controls only if the gate is closed: Set DIP2=OFF, switch-
on main power supply and wait for gate closing automatically.
PEDESTRIAN REMOTE CONTROL BUTTON STORE
- Push and release twice P1 button, Led automatically switches ON,
makes some lamps and switches ON again
- Push another Remote Control button, LED makes one blink, Remote is
stored,
Until LED is ON you can add more remote controls
- Wait for 10 seconds until LED switch OFF

MEMORY RESET

- Push and keep pushed P1 button, Led automatically switch ON
- Keep P1 push until LED switch OFF
- Release P1, LED makes ONE blink, Memory is free
SINGLE WING GATE SETTING (ONE MOTOR)
- Gate Closed
- Set Dip Switch N.1 = On
Press P1 Button On The Control Unit - Wing Opens
- Wing Is Opened - Wait For1 Or 2 Seconds - Press Remote Control Button To Stop It
- Wait For Desidered Pause Time In Opening (Normally Between 10 And 30 Secs.)
- Press Remote Control Button - Wing Closes
- Wing Is Closed - Wait For 1 Or 2 Seconds - Press Remote Control Button To Stop It
- Set Dip Switch N.1 = Off
FORCE ADJUSTMENT
- Gate Closed
- Press Remote Control Button – First Wing
Opens
- During The Opening Press P1 Button To
Decrease The 10% Of Force (Up To 6 Levels)
- Switch Off 230v Main Power
- Switch On 230v Main Power, Prog Led
Automatically Makes Some Lamps, Between 7
And 1 (7=Max 1=Min)
*If Set Dip 8 To On = Max Force (7 Lamps)
*fast closing function : during pause time the gate closes 3 seconds after having released photocells
REMOTE CONTROL (KEY FOBS)
FAST CLOSING*
- During Gate Time Setting, During
Desidered Pause Time (Gate Is Fully
Opened And Stopped)
- Activate Photocells For 2-3
Seconds – Prog Led Makes A Lamp
– Fast Closing Is Activated