JENN-AIR JDR8880RDW Manual De Instalación página 4

Ocultar thumbs Ver también para JDR8880RDW:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

ANTI-TIP DEVICE INSTALLATION INSTRUCTIONS
NOTE:
A risk of range tip over exists if the appliance is
not installed in accordance with the installation
instructions provided. The proper use of this device
minimizes the risk of TIP-OVER. In using this device the
consumer must still observe the safety precautions as
stated in the USE and CARE MANUAL and avoid using
the oven door and/or lower drawer as a step stool.
Installation instructions are provided for wood and cement
in either floor or wall. Any other type of construction may
require special installation techniques as deemed
necessary to provide adequate fastening of the ANTI-TIP
bracket to the floor or wall.
STEP 1 - - Locating The Bracket (see figure 1)
A. Determine where either the right or left rear "edge" of
the range will be located and mark the floor or wall.
B. Place the BRACKET 9/16" (14.5 mm) from the
marked "EDGE" toward center of opening and against
the back wall as shown in figure 1, with orientation
hole against wall.
C. Use the bracket as a template and mark the required
holes, as shown in figure 1 for the type of construction
you will be using.
STEP 2 - - Anti-Tip Bracket Installation
A. Wood Construction:
1. Floor: Locate the center of the two holes identified
in figure 1 as "HOLES FOR FLOOR". Drill a 1/8"
(3 mm) pilot hole in the center of each hole (a nail
or awl may be used if a drill is not available).
Secure the ANTI-TIP bracket to the floor with the
two screws provided. Proceed to STEP 3.
2. Wall: Locate the center of the two holes identified
in figure 1 as "HOLES FOR WALL. Drill an angled
1/8" (3 mm) pilot hole in the center of each hole
as shown in figure 2. (A nail or awl may be used if
a drill is not available). Secure the ANTI-TIP
bracket to the wall with the two screws provided
as shown in figure 2. Proceed to STEP 3.
9/16"
(14.5 mm)
FROM EDGE
OF RANGE
MARKED EDGE
OF RANGE
ORIENTATION
HOLE
ATTACH ANTI-TIP BRACKET WITH A
HOLES FOR
MINIMUM OF TWO (2) LONG SCREWS
WALL
TO THE WALL OR FLOOR.
ANTI-TIP
BRACKET
LEVELING
FOOT
HOLES FOR
FLOOR
(EACH SIDE)
FIGURE 1
B. Cement or Concrete Construction:
1. Suitable screws for concrete construction can be
obtained at a hardware store. Drill the required
size hole for the screws obtained into the
concrete at the center of the holes identified in
figure 1 as "HOLES FOR FLOOR". Secure the
ANTI-TIP bracket to the floor. Proceed to STEP 3.
STEP 3 - - Range Installation
A. For safety considerations as well as optimum
performance, adjust the range so it is level and to
desired height prior to installing in cabinet opening.
NOTE: Cooktop MUST be flush or above
countertop.
Levelness may be checked by placing a spirit level or
a large pan of water on the cooktop or oven rack.
Adjust the range by tipping it forward or back and
rotate the leveling feet as required.
NOTE: A minimum clearance of 1/4" (6 mm) is
required between the range and the leveling foot that
will engage the anti-tip bracket, (see figure 2).
CAUTION: Damage to the range may occur if range
is moved or lifted by grasping the main top, backguard
or door handles.
B. Align the range to its designated location and prepare
to slide it back into position. Connect gas line and
plug in power cord to outlet following guidelines
outlined in connecting the range and remainder of
installation instructions.
C. Slide range in place visually inspecting to verify that
power cord and gas line are freely routed and
contained within recessed area of back panel.
D. To check the range for proper installation of the
anti-tip bracket, use a flashlight and look underneath
the bottom of the range to see that one of the rear
leveling feet is engaged in the bracket slot.
NOTE:
USE A MINIMUM OF (2) SCREWS
TO INSTALL ANTI-TIP BRACKET
TO THE WALL OR FLOOR.
SCREWS MUST
ENTER WOOD
OR METAL.
WALL PLATE
--4--
ANTI-TIP
BRACKET
RANGE
SCREW BRACKET
BOTTOM
TO WALL
SLIDE IN
TO SECURE
FIGURE 2
1/4"
(6mm)
MIN.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Jdr8880rdsJdr8880rdb

Tabla de contenido