MIL'S HOSPIVAC 1 Manual De Operación Y Mantenimiento página 14

HOSPIVAC - MEDIVAC EVISA E25
INTRODUCTION
1.1. Specification plates ............................................................................................................................................ 13
DESCRIPTION
2.1. Vacuum pumps .................................................................................................................................................. 13
2.2. Receivers ............................................................................................................................................................ 13
2.3. Filtration and delivery pot ................................................................................................................................. 13
2.4. Electrical box ...................................................................................................................................................... 13
OPERATION
3.1. ON/OFF control regulation type ........................................................................................................................ 14
3.2. Constant vacuum regulation type in HOSPIVAC ................................................................................................ 14
CHOICE OF ROOM
REGULATION BY SENSOR OR BY VACUUM SWITCH
OUTLINE DIAGRAM
6.1. Mechanical architecture .................................................................................................................................... 15
INSTALLATIONS
7.1. For HOSPIVAC - MEDIVAC 1 and 2 / 3 ................................................................................................................ 15
7.2. For HOSPIVAC - MEDIVAC V ............................................................................................................................... 15
7.3. For HOSPIVAC G ................................................................................................................................................. 16
7.4. Power supply (see electrical circuit diagram attached) ..................................................................................... 17
7.5. Connections to the pneumatic network ............................................................................................................ 17
COMMISSIONING
First steps - Advice prior to commissioning the vacuum pumps ...................................................................... 18
8.1.
8.2. Switching on ....................................................................................................................................................... 18
SETTINGS
9.1. Setting pressure ................................................................................................................................................. 19
9.2. FLEXO time duration .......................................................................................................................................... 19
9.3. Top-up time duration ......................................................................................................................................... 19
9.4. Vacuum pump changeover time ........................................................................................................................ 19
ALARMS
10.1. For the MILLENIUM ............................................................................................................................................ 20
10.2. For the CYCLIC 2020 ........................................................................................................................................... 20
10.3. For the PROCOM-2 ............................................................................................................................................. 20
CLEANING AND MAINTENANCE
11.1. Filtration ............................................................................................................................................................ 21
11.2. Vacuum pump .................................................................................................................................................... 21
11.3. Checking operation of mechanical back-ups ..................................................................................................... 21
11.4. Exhaust vessel (emptying) ................................................................................................................................. 21
11.5. Changing the hose with vacuum applied ........................................................................................................... 21
11.6. Non-return valve ................................................................................................................................................ 21
Validation of sensor measurements - vacuum gauge ....................................................................................... 22
11.7.
11.8. Checking operation of the network alarm ......................................................................................................... 22
PRECAUTIONS WITH THE NETWORK
TRAINING
CLEANING
14.1. Units cleaning .................................................................................................................................................... 22
14.2. Network cleaning ............................................................................................................................................... 22
ELECTROMAGNETIC COMPATIBILITY
519991-06

E300
MEANING OF SYMBOLS USED IN THESE INSTRUCTIONS
13
Symbols are used in these instructions to help you understand them and to indicate particular points which
13
you need to act upon or consider. Those symbols are:
Reading symbol: to refer to the operator manual / instructions manual.
Warning symbol: This symbol means that failure to observe this point could lead to injury and
13
possibly damage to the machine. It serves as a special reminder about regulations and/or the correct
implementation of certain precautions.
14
Danger symbol: This symbol represents the DIN 4844 symbol (hazard warning); it warns of a hazard
15
which could result in death or injury, along with damage to the machine. This symbol must be
15
observed by all personnel working on this machine. Regulations on safety in the workplace must be
observed.
15
Environmental protection symbol: This symbol serves as a reminder to sort waste during
maintenance operations, to store it in a safe place, and to dispose of it with due care for the
environment.
Dustbin on wheels barred of a cross symbol: This symbol indicates that the equipment should not
18
be thrown with domestic waste and is subject to selective collection.
19 Biological hazard symbol: This pictogram informs of a risk or a danger, it is necessary to take care
to handle the biological products or waste being able to infect the living organisms by inhalation,
ingestion or cutaneous penetration.
Non-ionizing radiation hazard symbol: This pictogram informs of a risk or a danger related to non-
20
ionizing radiations
General remark:
20
If used in accordance with their intended purpose, units bearing the CE mark will satisfy the essential
requirements of directive 93/42/EEC relative to medical devices.
Those units, when installed in accordance with these instructions, comply with the provisions of currently
applicable European Directives and harmonised standards.
However, your attention is drawn to the fact that a unit with only one compressor or only one vacuum pump
cannot be used without an emergency backup device: gas backup or other fixed or mobile unit.
22
22
To ensure personal safety and to avoid any damage to equipment, it is essential to follow
22
the instructions contained in this document and any other documentation provided with
the de i e, a d pa ti ula l the i st u tio s o
22
"afe P a ti e .
12