Technical Data; Attachment And Operation - Scheppach LB5200BP Instrucciones Originales

6. Technical data

LB5200BP
Technical data
Dimension LxWxH mm
Air speed max. km/h
air volume max. m /min
3
dust bag capacity l
Power unit
Displacement cm
3
Max. engine output kW
Idle speed min
-1
Fuel tank capicity cm
3
Engine type
Weight kg
Subject to technical changes!
Information concerning noise emission measured ac-
cording to relevant standards:
Sound pressure L = 94,0 dB(A)
pA
Sound power L = 110 dB(A)
WA
Uncertainty K = 3 dB(A)
PA
Wear ear­muffs.
The impact of noise can cause damage to hearing.
Vibration A = 1,655 m/s
2
hv
Uncertainty K = 1.5 m/s
2
PA
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves.
In these operating instructions we have marked
the places that have to do with your safety with
this sign: m

7. Attachment and operation

ATTENTION! Before working on the device ­ clean-
ing, inspection, maintenance or other work ­ always
turn off the device.
Assembly (Fig. 6-6c)
m WARNING: The blower must not be used or
switched on until it has been fully assembled.
Attach the two hose clamps (17A and 17B) to the
•
flexible blowpipe (12).
Push the flexible blowpipe (12) over the connection
•
to the motor unit and tighten the hose clamp (17B)
firmly (Fig. 6).
Now push the handle (1) over the upper blowpipe
•
(13). Align the handgrip (1) and the guide in the same
way, fold it together and then tighten it (Fig. 6a).
20 GB
1380x400x450
295
18
-
51,7
1,4
3500 ± 300
1000
2­stroke engine, air­
cooled
7,84
Push the upper blowpipe into the flexible blow hose
•
(12) with the handle and fix it with the hose clamp
(17A) (Fig. 6b).
Push the lower blowpipe (14) over the upper blowpipe
•
(13) and lock it in the clockwise direction (Fig. 6c)
The blower nozzle (No. 15) is simply pushed over
•
the lower blowpipe (No. 14) and locked in the clock-
wise direction (Fig. 6c).
m Warning! Use only original manufacturer's re-
placement parts, accessories and attachments. Fail-
ure to do so can cause poor performance, possible
injury and may void your warranty. Never use the
machine without the guard assembled!
Operation
Before starting
Place the carrying strap
Pull the belt down, the straps are tightened
Loosen the straps
Lift the clamping slide
Adjust the carrying strap so that the back plate rests
firmly and securely against t
Each time before use, check the following:
• That there are no leaks in the fuel system.
• That the equipment is in perfect condition and that
the safety devices and cutting devices are com-
plete.
• That all screws are securely fastened.
• That all moving parts move smoothly.
Fuel and oil
Recommended fuels
Use only a mixture of unleaded petrol and special
2­stroke engine oil. Mix the fuel mixture as indicated
in the fuel mixing table.
Important: Do not use a fuel mixture which has
been stored for longer than 90 days.
Important: Never use 2­stroke oil with a recommend-
ed mixing ratio of 100:1. The manufacturer's war-
ranty will be voided in case of engine damage due to
inadequate lubrication.
Important: Only use containers designed and ap-
proved for the purpose to transport and store fuel.
Pour the correct quantities of petrol and 2­stroke oil
into the mixing bottle (see scale printed on the bot-
tle). Then shake the bottle well.
Never use oil for 4-cycle engine or use water cooled
2­cycle engine. It can cause spark plug fouling ex-
haust part blocking or piston ring sticking.
Mixed fuels, which have been left unused for a pe-
riod of one month or more, may clog the carburetor
or result in the engine foiling to operate property. Put
remained fuel into an airtight container and keep it in
the dark and cool room.