Campbell Hausfeld IFN35650 Instrucciones De Operación

See Warranty on page 7 for important information about commercial use of this product.
Operating Instructions
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury, death
and/or property damage! Retain instructions for future reference.
Table Of Contents
General Safety . . . . . . . . . . . . . . . 1 - 3
Specifications . . . . . . . . . . . . . . . . . . 2
Operational Modes . . . . . . . . . . . . . 4
Operating The Nailer . . . . . . . . . 3 - 5
Troubleshooting . . . . . . . . . . . . . . . 6
Warranty . . . . . . . . . . . . . . . . . . . . . 7
Description
This nailer is designed for decorative
trim, molding, window casings,
furniture trim and picture frame
assembly. Features include: convenient
rear loading magazine which holds up to
100 nails, no-mar tip, adjustable exhaust,
single cycle trigger, quick clear nose, and
an adjustable depth of drive mechanism.
General Safety
Information
CALIFORNIA PROPOSITION 65
You can create dust when
you cut, sand, drill or grind
materials such as wood,
paint, metal, concrete, cement, or
other masonry. This dust often
contains chemicals known to cause
cancer, birth defects, or other
reproductive harm. Wear protective
gear.
Excessive exposure to vibration,
working in awkward positions and
repetitive work motions can cause
injury to hands and arms. Stop using
any tool if discomfort, numbness,
tingling or pain occur and consult a
physician.
Campbell Hausfeld Nailers meet or exceed Industries' Standards as set forth by the American National
Standard Institute/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002.
© 2008 Campbell Hausfeld/Scott Fetzer
This manual contains safety,
operational and maintenance
information.
Read this manual and
understand all safety
warnings and instructions
before operating the
nailer. Contact your
Campbell Hausfeld
representative if you have any
questions.
OPERATOR'S RESPONSIBILITY:
Before operating the nailer, read and
understand all safety warnings and
labels. Follow the operating
instructions outlined in this manual.
EMPLOYER'S RESPONSIBILITY:
Distribute this instruction manual to all
users before allowing use of the nailer.
Ensure all operators read, understand
and follow all safety warnings, labels
and instructions outlined in this
manual.
DANGER
!
hazardous situation which, if not
avoided, WILL result in death or serious
injury.
• Do not use any type
of flammable gases
or oxygen as a power
source for the nailer.
Use filtered,
lubricated, regulated
compressed air only.
Use of a compressed gas instead of
compressed air may cause the nailer
to explode which will cause death or
serious personal injury.
• Do not exceed
maximum operating
pressure of the nailer
(120 psi). The nailer
will not function
properly. Do not use
a compressed air
source capable of more than 200 PSI.
REMINDER: Keep your dated proof of purchase for warranty purposes!
Attach it to this manual or file it for safekeeping.
For parts, product & service information
visit www.chpower.com
Angle Finish Nailer
MANUAL
Danger indicates
an imminently
O
CO
2
Model IFN35650
Model IFN35650
Locate model and date code on
tool and record below:
Model No. ______________________
Date Code ______________________
Retain these numbers for
future reference.
The nailer could explode which will
cause death or serious personal
injury.
• Never use gasoline
or other flammable
liquids to clean the
nailer. Never use the
nailer in the presence
of flammable liquids
or gases. Vapors could ignite by a
spark and cause an explosion which
will result in death or serious
personal injury.
• Always remain in
a firmly balanced
position when
using or handling
the nailer.
• Do not modify or
disable the Work
Contact Element
(WCE). Do not tie
or tape the WCE
or trigger in a
depressed
position. Death or serious personal
injury could result.
IN725300AV 2/08