LEXIBOOK Serenity Manual Del Usuario página 12

Setting the Awakening Alarm Mode
®
The Serenity Clock features an innovative Awakening Mode. Wake up gently with the sounds of nature, soothing music and
soft light effects. The duration of the awakening period can be set. The awakening sequence will start before the set time to
wake up the user in a natural way until the set alarm time is reached. It is also possible to wake up without light effects.
There are 3 user-selectable awakening themes:
Countryside: sounds of streams, birds, bells, sheep ...
New Age: virtual music...
Ocean: sounds of waves, dolphins, seagulls, boats ...
At the beginning of the awakening sequence the sound will be in low volume and the light dim. During the wake up period the
volume will gradually increase and more sounds will be added until the maximum level is reached at the set wake up time. Also,
the light intensity is increasing over time to simulate the raising sun and tell the sleeping body that the night is over and a new
day is dawning. To enjoy the awakening experience to the most, set the awakening period and volume to your preference.
1. Select an awakening theme
In clock display mode, press until is displayed to activate the awakening alarm mode. Press
between the 3 themes available (Ocean = , Countryside =
be selected. Press and hold to preview the alarm tone.
2. Set the alarm time (end time)
Note that the alarm time is actually the time at which you want the alarm or awakening period to stop. By selecting the duration
of the awakening period in the next step, you will set the alarm starting time.
3. Set the duration of the awakening (start time)
Press and hold for 2 seconds while in clock mode. Press
top part of the screen. The duration of the awakening period can be set to 15, 30 or 45 minutes. Press
the time of the awakening period, and confirm with
to activate (TOP ON) or deactivate (TOP OFF) the light show during the awakening period. Press
between TOP ON and TOP OFF, and confirm with
display mode.
20-21
to toggle
, New Age = ). The currently displayed ringtone will
once. is flashing and DUR 15 is displayed on the
or
. TOP ON is displayed on top of the screen. Select whether you want
or
. Press three times to confirm your settings and return to clock
0
When the alarm rings
is flashing and the awakening sequence begins. Press any key except
again the next day at the same time. If the alarm is not stopped, it will automatically end at the time set.
OR
Press to repeat (snooze) the alarm (the whole awakening sequence will be repeated).
The slumber mode has been developed with our busy and hectic lifestyle in mind. It calms the mind and prepares the body for a
good night sleep. The same themes as for awakening mode can be selected, and the slumber duration as well as the lightshow
on or off can be set. The sequence will start on maximum volume. Slowly the volume will decrease and fewer and fewer sounds
are played. The light intensity will gradually be reduced to give the impression of a peaceful sunset. As the light is fading and the
sounds fade the user is falling into a healthy sleep. If an alarm is set for the next day, the volume should not be set too low as
otherwise the sounds might not be heard and the user will oversleep.
1. Enter the slumber theme set mode
Press and hold for 2 seconds while in clock mode. The currently selected slumber theme is displayed and a preview is
playing. Press or
Confirm with to return to clock display mode.
2. Set the duration of the slumber mode
Press and hold for 2 seconds while in clock mode. Press
top part of the screen. The duration of the slumber period can be set to 15, 30 or 45 minutes. Press
time of the slumber period, and confirm with
activate (TOP ON) or deactivate (TOP OFF) the light show during the slumber period. Press
between TOP ON and TOP OFF, and confirm with
display mode.
to set
3. Turn the slumber mode on
to toggle
When you are ready to go to sleep, press
you wish to turn it off.
to end the awakening period. It will start
Slumber Mode
to toggle between the 3 themes available (Ocean = , Countryside =
twice. is flashing and DUR 15 is displayed on the
. TOP ON is displayed on top of the screen. Select whether you want to
. Press once more to confirm your settings and return to clock
to launch the slumber mode while in clock mode. Press
21
, New Age = ).
or to set the
or to toggle
once more if
21/07/2006 17:54:30