Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
8
3.1. DEVICE DESCRIPTION
3
5
3
4
6
1
1
2
2
2
2
1.
Chassis foot
2.
Adjustable feet
3.
Side brackets
4.
Adjustment rod
5.
Transverse rail
6.
Adjustment rod crank
3.2. PREPARING FOR USE
The device should always be used when positioned on an
even, stable, clean, fireproof and dry surface, and be out of
the reach of children and persons with limited mental and
sensory functions.
ELEMENTS LIST:
A(x1)
B(x1)
C(x2)
D(x2)
E(x1)
F(x1)
G(x1)
A.
Transverse rail
B.
Adjustment rod
C.
Side bracket
D.
Foot
E.
Drive rod module
F.
Left lifting column
G
Right up column
CONNECTION ELEMENTS
S-A(x16)
S-B(x4)
S-C(x10)
S-D(x1)
S-A
Hexagon head screws
S-B
Philips-head screws
S-C
Philips -head screws with flange
S-D
Allen key
EN
Warning! Before assembling the device, make sure that
the number of items in the packaging corresponds to the
list of items contained in this manual.
DEVICE INSTALLATION
Before installation, prepare and secure the appropriate space.
It
is
recommended
to
use
a
protective
or
pad
to
prevent
product
/
floor
scratches.
MOUNTING THE TRANSVERSE RAIL:
•
Loosen the S-D screws on the transverse rail A, but
do not remove the screws completely. Extend the
element and set the correct rail length (See the
figure below).
S-D
A
•
Retighten all S-D screws to complete the adjustment.
S-D
S-D
INSTALLATION OF LIFTING COLUMNS:
•
Install a lifting column (F or G) to one end of
transverse rail A.
•
Make sure that the holes in the individual legs match
the holes in the mounts.
•
Use S-A screws to tighten them with an S-D allen key
(see figure below).
G
F
S-A
S-D
INSTALLING THE SIDE BRACKET:
•
Install the C side bracket to one end of the transverse
rail A with two S-A screws and tighten them using
the S-D Allen key (the picture below).
•
Repeat the above step to install the second side
bracket.
S-A
C
S-D
PREPARATION OF THE COUNTER FOR ASSEMBLY
( DRILLING OF MOUNTING HOLES ) :
Before mounting, make sure you need to drill holes in the
countertop.
•
Place the counter on a safe surface to avoid damage.
Use the drill to make eight holes corresponding to
mat
the spacing of the holes in the side bracket (the
figure below)
CAUTION! The mounting holes should be over 70 mm
deep and the diameter should be less than 3 mm.
FOOT ASSEMBLY
•
Fasten foot D to the bottom of the lifting column (F
/ G). Make sure the holes in the foot match the holes
in the lifting column. Using four S-A screws, tighten
them with an S-D Allen key (picture below)
•
Repeat the above step to mount the second foot.
•
After mounting the feet, the structures should be
turned over and put on the feet.
S-D
S-A
D
INSTALLATION OF THE ADJUSTMENT ROD
Warning! When rotating the desk structure, at least two
people are needed to install the rod.
•
Unscrew the knob clockwise to loosen the rod, then
adjust the width of the rod to the width of the frame
(the figure below).
•
Install the rod at the feet of the frame.
•
Turn the knob to lock the adjustment.
1
2
EN
9
3
COUNTER INSTALLATION
The counter with properly selected holes should be placed
on side brackets C. Tighten screws S-C (x10).
S-C
INSTALLATION OF DRIVE ROD MODULE:
•
Install the E-rod assembly in the gearing box in the
right foot.
•
Using
an
Allen
key,
unscrew
counterclockwise and adjust the length (fig. 1 below).
•
Place the rod in the module.
•
Tighten the screw on the module to lock the rod (fig.
3 below).
•
The module should be screwed to the top using S-B
screws and a Phillips screwdriver as shown in the
drawings below.
1
3
S-D
4
2
S-B
E
the
screw
Publicidad
Tabla de contenido
