Publicidad
Enlaces rápidos
SLIDING DOOR HARDWARE - BY PASS
BYP-175I & BYP-275I •
each with thickness of 1" to 1-3/4"
Tools Required • Outils requis • Herramientas requeridos
Wrench - 1/2" (included) • Clé - 1/2" (incluse) • Llave - 1/2" (incluida)
Drill (1/8", 3/8", 3/32") • Perceuse (1/8", 3/8", 3/32") • Taladro (1/8",3/8", 3/32")
Phillips Screw Driver • Tournevis Phillips • Destornillador Phillips
Fine Tooth Saw (optional) • Scie à dents fines (optionnelle) • Sierra de dientes finos (opcional)
CONTENTS
A. Track
B. Carrier
C. Door Mount Plate
D. Adjusting Screw
E. Floor Guide
F. #10 x 1-1/2" Pan Head Screw
G. #6 x 7/8" Flat Head Screw
H. #12 x 1-1/4" Pan Head Screw
QUINCAILLERIE POUR PORTE COULISSANTE – BY PASS
BYP-175I & BYP-275I •
d'une épasseur de 2,5 cm à 4,4 cm
CONTENU
A. Coulisse
B. Rouleaux décalés
C. Plaque de montage de porte
D. Vis d'ajustement
E. Guide de plancher
HERRAJE PARA PUERTA CORREDIZA - TIPO BY PASS
BYP-125A & BYP-150A •
cada una y de 2,5 cm à 4,4 cm de grosor
CONTENIDO
A. Caril
B. Portador
C. Placa de montaje de puerta
D. Tornillo de ajuste
E. Guía del piso
For 2 doors up to 175 lbs. (2-wheel) & 275 lbs. (4-wheel)
2-Door
2
B.
4
4
4
2
40
8
16
C.
Pour 2 jusqu'à 79,3 kg (2-roue) y 124,7 kg (4-roues) chacune
2-Portes
2
4
4
4
2
Para 2 puertasde hasta 79,3 kg (2-rueda) y 124,7 kg (4-rueda)
2-Puertas
2
4
4
4
2
OR
E.
CONTENU
F. #10 x 1-1/2" Vis à tête bombée
G. #6 x 7/8" Vis à tête plate
H. #12 x 1-1/4" Vis tête cylindrique
CONTENIDO
F. #8 x 5/8" Tornillos cabeza plana
G. #8 x 3/4" Tornillo cabeza plana
H. #8 x 1-1/2" Tornillos cabeza plana
#310305_B (1112)
Assembly
Instructions
A.
D.
F.
H.
G.
#310305_B (1112)
Instructions
d'assemblage
2-Portes
40
8
16
#310305_B (1112)
Instrucciones para
el ensamblaje
2-Puertas
40
8
16
Publicidad
Manuales relacionados para Knape & Vogt BY PASS BYP-175I
Resumen de contenidos para Knape & Vogt BY PASS BYP-175I
- Página 1 SLIDING DOOR HARDWARE - BY PASS #310305_B (1112) Assembly BYP-175I & BYP-275I • For 2 doors up to 175 lbs. (2-wheel) & 275 lbs. (4-wheel) Instructions each with thickness of 1” to 1-3/4" Tools Required • Outils requis • Herramientas requeridos Wrench - 1/2"...
- Página 2 #310305_B (1112) SLIDING DOOR HARDWARE - BY PASS Assembly Instructions PREPARE OPENING Hmax = Door Height + 4-1/8" • Hmin = Door Height + 3-3/8" 3" - 3-3/4" (7,6 cm - 9,5 cm) 2-Door Width = 2 x Door Width - 1" Opening Height Hauteur Ouverture Altura Abertura...
- Página 3 #310305_B (1112) SLIDING DOOR HARDWARE - BY PASS Assembly Instructions HANG DOORS • Cut a continuous slot in bottom of door, centered as shown below. • Open quick release latches on brackets. • Slide door onto carrier screws and close latch. •...
- Página 4 QUINCAILLERIE POUR PORTE COULISSANTE - BY PASS Instructions d’assemblage Instrucciones para HERRAJE PARA PUERTA CORREDIZA - TIPO BY PASS el ensamblaje PRÉPARATION DE PREPARAR ABERTURA L’OUVERTURE Altura máxima = Altura de la puerta + 10,5 cm Altura mínima = Altura de la puerta + 8,6 cm Hmax = Haut.