Status Indicators; Initial Setup - VT Miltope nMAP2 Guia De Inicio Rapido

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Connector J3 provides connection for Ethernet ports 1 and 3.
Pin*
Signal
1
Port 1 Bidirectional Pair B+
2
Port 1 Bidirectional Pair A+
3
Port 1 A/B Inner Shield
4
Port 1 Bidirectional Pair D+
5
Port 1 Bidirectional Pair C+
* Use Deutsch shell DMC-MD 20C, insert & contacts DMC-M 20-22SN, backshell 787-8055-13M or equivalent for mating connector.

STATUS INDICATORS

Indicator
POWER Indicator
Lit solid green to indicate powered up and enabled for operation. Flashes to indicate powered up, but operation is
disabled (standby mode). The internal unmanaged Ethernet switch continues to function in standby mode.
RF ENABLE Indicator
Lit solid green to indicate RF output is enabled.
WLAN Indicators
Flash green to indicate RF data transfers are occurring on the applicable radio card.
LAN Indicators
Flash green to indicate applicable LAN data transfers are occurring.
Lit solid green to indicate that a link is established on applicable wired LAN ports, but no data transfers are occurring.

INITIAL SETUP

Connect the nMAP2 Access Point in the lab environment as shown:
COMPUTER WITH 10/100/1000BASETX
ETHERNET CAPABILITY
WHAT IS IN THE BOX: nMAP-2 WIRELESS ACCESS POINT PART NUMBER 903920-1
EQUIPMENT REQUIRED, BUT NOT SUPPLIED:
DESKTOP COMPUTER WITH 10/100/1000 BASE TX ETHERNET CAPABILITY
LAPTOP COMPUTER WITH IEEE 802.11a/g (IEEE 802.11a/ac/g/n
RECOMMENDED) WIRELESS CAPABILITY AND SETTABLE WIRELESS MODE
TEST BOX, MILTOPE PART NUMBER CT2014-013
J1 TEST CABLE, MILTOPE PART NUMBER CT2014-016
J2 TEST CABLE, MILTOPE PART NUMBER CT2014-017
J3 TEST CABLE, MILTOPE PART NUMBER CT2014-018
Pin*
Signal
6
Port 1 Bidirectional Pair A-
7
Port 1 Bidirectional Pair B-
8
Port 1 C/D Inner Shield
9
Port 1 Bidirectional Pair C-
10
Port 1 Bidirectional Pair D-
J3 TEST CABLE MILTOPE
PART NUMBER CT2014-018
P4
ETHERNET
LAN PORT 1
USE OF P5 (LAN PORT 3) IS OPTIONAL FOR
CONNECTION TO AN ADDITIONAL COMPUTER
Pin*
Signal
11
Port 3 Bidirectional Pair B+
12
Port 3 Bidirectional Pair A+
13
Port 3 A/B Inner Shield
14
Port 3 Bidirectional Pair D+
15
Port 3 Bidirectional Pair C+
Function
nMAP2 WIRELESS ACCESS POINT
J3
J2
J1
P1
P3
P2
J2 TEST CABLE MILTOPE PART
NUMBER CT2014-017
P6
P5
USE OF J2 TEST CABLE IS
(LAN
OPTIONAL FOR CONNECTION
PORT 2)
TO AN ADDITIONAL COMPUTER
J1 TEST CABLE MILTOPE
PART NUMBER CT2014-016
P3
RED (POS) BLK (RTN)
115 VAC
28 VDC
OR
(97 - 134 VAC)
(18 - 32 VDC)
360 - 800 Hz
INPUT POWER
INPUT POWER
3
Pin*
16
Port 3 Bidirectional Pair A-
17
Port 3 Bidirectional Pair B-
18
Port 3 C/D Inner Shield
19
Port 3 Bidirectional Pair C-
20
Port 3 Bidirectional Pair D-
PART NUMBER CT2014-013
LAPTOP COMPUTER WITH
IEEE 802.11a/g CAPABILITY
(IEEE 802.11a/ac/g/n RECOMMENDED)
Signal
TEST BOX MILTOPE
P2
J1
1408201B

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

903920-1

Tabla de contenido