VT Miltope nMAP2 Guia De Inicio Rapido página 5

I. Refer to nMAP2 Wireless Access Point Operating Software
Operator's Manual M365-768 for detailed instructions for
configuring the nMAP2 access point for a specific application.
NOTE: Selecting the country of operation during the configuration
process will limit radio configuration to settings that comply
with the regulatory requirements of the selected country.
The default country setting is USA.
0.25
6X 0.203 (5.16)
(6.3)
MOUNTING HOLES
0.09
0.563 (14.29) MASKED
(2.29)
AREA AROUND
MOUNTING HOLES
FOR GROUNDING
8.89
(225.81)
9.47
(240.52)
5.70
±0.25
144.78
±6.35)
1.31
(33.15)
0.38
1.30
(9.53)
±0.25
2.28
1.02
(33.02
(57.79)
(25.79)
±6.35)
2.89 (73.35)
7.35 (186.69) MAX
0.29
6.39 (162.31)
(7.3)
5.43 (137.95)
3.30±0.25
(83.82±6.35)
10.750
(273.05)
2.750 (69.85)
0.733
5.500 (139.7)
(18.61)
6.97 (176.91)
nMAP2 Access Point Outline Drawing
INSTALLATION
The nMAP2 Wireless Access Point must be installed by personnel
qualified and authorized to install equipment aboard an aircraft.
Mounting the nMAP2 Access Point – As shown in the nMAP2 access
point outline drawing, six mounting holes are provided. Mount the
nMAP2 access point using number 10-24 mounting hardware.
Recommended torque value for mounting hardware is 24.0 inch-
pounds. Although not mandatory for specification compliance, it is
recommended that the nMAP2 access point be mounted to a grounded
surface within the aircraft. An unpainted area around each mounting
hole provides ground connection to the mounting surface.
2.51 (63.82)
8-32 UNC-2B THREADED
REF
GROUND POINT
0.28 (7.1) MAX
SCREW DEPTH
FROM FACE,
20±1.0 IN-LBS
MAX TORQUE
ANTENNA
RADOME
6.63
(168.39)
REF
11.50
(292.1)
5X
1.33
9.20
(33.68)
(233.56)
REF
REF
2.44
(61.97)
REF
4X R 0.43 (11.02) REF
4X R 0.25 (6.35) REF
5
1.85 (46.88) REF
1.47 (37.37)
0.80 (20.39) REF
NOTES:
1. Primary dimensions are in inches.
2. Dimensions in parenthesis are in millimeters.
3. Tolerances:
X.XX (2 Places) = ±0.04 (±1.02)
X.XXX (3 Places) = ±0.010 (±0.25)
4. denotes center of gravity.
5. Maintain minimum 2 inches (50.8 mm)
between nMAP2 and aircraft insulation on all
four sides and antenna radome surface.
WARNING
THE nMAP2 ANTENNA RADIATES
RADIO FREQUENCY (RF) POWER.
TO AVOID EXCEEDING FEDERAL
COMMUNICATIONS COMMISSION
(FCC) RADIO FREQUENCY
EXPOSURE LIMITS, HUMAN
PROXIMITY TO THE nMAP2 SHALL
BE NO LESS THAN EIGHT INCHES
6.46
(20 CENTIMETERS) WHILE RF IS
(164.05)
ENABLED.
REF
7.88
5.04
(200.03)
(128.07)
REF
REF
1409231A