Eden World Tour Pro Serie Guia De Inicio Rapido página 7

EDEN | WTP SERIES | REAR PANEL FEATURES - 8
OFF: When the indicator is off you are not clipping the power stage of the amplifier.
AMBER: If the indicator illuminates amber this means you have clipped the input stage of the amplifier briefly but not for a
prolonged period of time. If the indicator operates only in the amber stage you are getting the maximum from the input stage of
the amplifier without causing undesirable clipping to your sound.
RED: When the indicator illuminates red it will stay on for at least 1 second or continually to indicate clipping of the power
amplifier. If the indicator flashes red this means that you are using the amplifier outside of its correct limits and the amplifier is
overheating this will cause the amplifier to go into a safe mode reducing the chance of long term damage to the amplifier by
increasing the cooling of the unit and lowering the output volume of the amplifier.
26. Master Volume: This adjusts the output volume of the amplifier. Use this control in conjunction with the output clip indicators (on
powered units only) to achieve the best performance from your amplifier.
27. Illuminated Logo: Logo illuminates when amplifier is switched on.
28. OFF / ON switch: Turn your amplifier off or on using this switch.
29. Cooling Vent: Provides ventilation for the units cooling system. NEVER OBSTRUCT OR MODIFY THIS OR ANY OTHER VENT ON
YOUR UNIT.
REAR PANEL FEATURES
(For WTP900, WTP600 and WTPre)
Features will be the same for each model except where the functionality is changed due to the absence of one or more power amplifiers
in the product.
Depending on the model you own your World Tour Pro series product may be fitted with up to 3 internal fans. When turning the unit on
these fans will briefly run up and then switch off again. The Fans in World Tour Pro products are only designed to activate when the unit
becomes hot. It is normal for the fans to remain off if not required by the amplifier
Cooling Vent: Provides ventilation for the units cooling system. NEVER OBSTRUCT OR MODIFY THIS OR ANY OTHER VENT ON
YOUR UNIT.
Power Input: Plug your unit in here. Please ensure your unit is of the correct voltage for your region and that you only use an Eden
supplied power cable.
1 2 | H I F I D E L I T Y F O R L O W F R E Q U E N C Y
EDEN | WTP SERIES | WTP900 REAR PANEL FEATURES - 9
World Tour Pro 900 Rear Panel Features
SPEAKER OUTPUTS: The Eden Illuminated Output System used on World Tour Pro amplifiers has been designed by Eden to more
easily allow players to make the right choices with their rig selection. Because the sockets are illuminated, it allows you to simply
select the mode that suits your cabinets ensuring you get the best performance with the equipment you own.
Each mode selected switches between bridge / bi-amp and represents the correct cabinet impedance that should be used with the
associated socket, Green indicates 4ohm compatibility, Amber indicates 8ohm compatibility and red indicates that the socket should
not be used.
Bridge Series: In addition to standard modes the World Tour Pro 900 is able to run in Bridge Series Mode. When engaged the
amplifier can be used in bridged mode with 2 - 4ohm cabinets.
1. Speaker Output 1: Depending on selected mode, connect the correct impedance cabinet here using a Speakon speaker lead here.
2. Speaker Output 2: Depending on selected mode, connect the correct impedance cabinet here using a Speakon speaker lead here.
3. Amp Left Speaker 2 Output: Depending on selected mode, connect the correct impedance cabinet here using a Speakon speaker lead
here.
4. Amp Right Speaker 2 Output: Depending on selected mode, connect the correct impedance cabinet here using a Speakon speaker lead
here.
5. Output Left: Take your left signal output (post loop) to external equipment here.
6. Output Right: Take your right signal output (post loop) to external equipment here.
7. Aux Input: Connect Auxiliary input signal from your MP3 player or other device using 3.5mm jack cable here.
8. Headphones: Connect your headphones using this 3.5mm output (the headphone volume is controlled by the Master Volume control on
the amplifier front panel).
9. Stereo Loop Return L: Return your left effect chain signal here.
10. Stereo Loop Return R: Return your right effect chain signal here.
11. Balance Control: Use this control to balance the level between the two amplifiers.
12. Stereo Loop Send L: Send your left effect chain signal out from here.
H I F I D E L I T Y F O R L O W F R E Q U E N C Y | 1 3